Service Parts List S/N C14C

ManualsBrandsMilwaukee ManualsTools & HardwareM18 18-Volt Lithium-Ion Cordless Band Saw (Tool-Only)

CORDLESS 18V COMPACT BAND SAW

2629-20

C14C

54-40-2602

SEE PAGES 5, 6, 7 & 8

Aug. 2014

REVISED BULLETIN

54-40-2601

SERVICE PARTS LIST

BULLETIN NO.

WIRING INSTRUCTION

DATE

SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS

CATALOG NO.

MILWAUKEE ELECTRIC TOOL CORPORATION

13135 W. LISBON RD., BROOKFIELD, WI 53005

Drwg. 2

STARTING

SERIAL NO.

EXAMPLE:

Component Parts (Small #)

Are Included When Ordering

The Assembly (Large #).

GEAR ASSEMBLIES

#105 & #106 MUST BE

ORDERED AS A SET

CAT. NO. 32-05-2629

74 (6X)

89 (2X)

90 (2X)

55 (3X)

48 (2X)

83 82 80 81 53 (4X)

86 79 77

36 (3X)

109

108

57 58

59 60

105

106

67 68

70 71

107

20 39

74 (6X)

77 84 85

92 93

110

(4X)

116

114

(2x)

115

113

(2x)

113 114

115 116

117

118

(4X)

(3X)

Soldered

Screwed

#118 two styles

of Brush Card

Assemblies

See Page Two

SEE ADJACENT PAGES

FOR ADDITIONAL SERVICE

NOTES, LUBRICATION

AND WIRING

FIG. PART NO. DESCRIPTION OF PART NO. REQ.

35 06-82-5574 10-24 x 7/8" Pan Hd. Tapt. T-25 Screw (7)

36 06-82-0035 M5 Pan Hd. T-20 Screw (3)

39 --------------- Deck (1)

47 --------------- Brush Card (1)

48 22-56-0150 Wire Nut (C1 & C2) (2)

50 18-01-3015 Service Field (1)

52 16-01-3091 Service Armature (1)

53 05-78-0305 Switch Screw (4)

54 45-88-1890 Spring Washer (4)

55 06-82-5320 8-32 x 5/8" Pan Hd. Slt. Tapt. T-20 Screw (3)

56 28-28-0060 Diaphragm (1)

57 02-04-0645 Ball Bearing (1)

58 --------------- 1st Gear (1)

59 --------------- Ball Bearing (1)

60 --------------- 2nd Bevel Pinion (1)

61 --------------- Bevel/Spur Gear (1)

62 --------------- Needle Bearing (2)

63 --------------- Gearcase (1)

64 02-04-0135 Ball Bearing (1)

66 45-30-0255 Rubber Slug (4)

67 --------------- 3rd Gear (1)

68 --------------- Pulley Shaft (1)

69 43-96-0105 Key (1)

70 02-04-1525 Ball Bearing (1)

71 45-88-0406 Washer (1)

72 28-14-0180 Bearing Plate Bottom (1)

73 06-82-7261 6-19 x 11/16" Pan Hd. Slt. Plast. T-15 Screw (2)

74 06-82-7270 8-16 x 5/8" Pan Hd. Slt. Plast. T-20 Screw (12)

75 --------------- Handle - Left (1)

76 40-50-0650 Compression Spring (1)

77 --------------- Terminal Block Assembly (1)

78 42-55-0100 Carrying Case (1)

79 06-82-5294 1/4-20 x 3/4" Pan Hd. Tapt. T-30 Screw (2)

80 23-66-1000 Switch (1)

81 06-82-7251 8-16 x 3/8" Pan Hd. Slt. Plast. T-20 Screw (1)

82 --------------- Lock-Off Shuttle (1)

83 40-50-0665 Detent Spring (1)

84 10-20-1865 LED Label (1)

85 --------------- PCB (1)

86 --------------- Handle - Right (1)

87 06-82-0045 3/8"-16 UNC-3A Hex Recess Screw (1)

88 31-44-0095 Front T-Handle (1)

89 06-82-5316 8-32 x 1/2" Pan Hd. Slt. Tapt. T-20 Screw (2)

90 45-88-0825 Washer (2)

91 --------------- Motor Cover (1)

92 --------------- Wire Assembly (1)

93 --------------- LED Switch Box (1)

94 31-44-0305 Handle Kit (1)

95 31-15-0205 Motor Cover Assembly (1)

96 28-90-0015 Deck Assembly (1)

107 14-73-0040 Pulley Gear Assembly (1)

108 14-30-0050 Top Gearcase Assembly (1)

109 45-24-0055 Shuttle Lock-Off Kit (1)

110 14-20-0025 Electronics Kit (1)

113 05-88-0928 M3 x 5mm Pan Hd. T-10 Screw (2)

114 45-88-1980 Spring washer (2)

115 --------------- Leadwire Assembly - Black (1)

116 --------------- Leadwire Assembly - Red (1)

117 14-46-2397 Leadwire/Screw/Washer Kit (1)

118 14-46-2016 Brush Card Assembly (1)

FIG. NOTE:

64,70 Orient the Ball Bearings so the seal faces the gears.

68 Apply approximately .1g Loctite

C5-A Copper Anti-Seize (or equivalent) to bottom

portion of Pulley Shaft that ﬁ ts into Rear Pulley (4).

105  Bevel Pinion Assembly (1)

106  Bevel/Spur Gear Assy. (1)

ORDER AS A SET

Cat. No. 32-05-2629

}

Summary of content (8 pages)

PAGE 1
BULLETIN NO. SERVICE PARTS LIST 54-40-2602 SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS 00 EXAMPLE: 0 Component Parts (Small #) Are Included When Ordering The Assembly (Large #). FIG. PART NO. 35 06-82-5574 36 06-82-0035 39 --------------47 --------------48 22-56-0150 REVISED BULLETIN DATE 54-40-2601 Aug. 2014 CORDLESS 18V COMPACT BAND SAW STARTING CATALOG NO. 2629-20 C14C SERIAL NO. 83 DESCRIPTION OF PART 10-24 x 7/8" Pan Hd. Tapt. T-25 Screw M5 Pan Hd.
PAGE 2
SolderedOriginal design ScrewedNew design NOTE: There are two Brush Card Assembly designs. On the original brush card design the red and black wires that go to the switch are soldered on the brush card. On the new brush card design the red and black wires that go to the switch are secured to the brush card with spring washers and screws. The new brush card design is directly interchangeable in tools that have the old brush card design.
PAGE 3
= Part number change from previous service parts list. 44 104 41 45 46 34 (9x) 46 45 40 39 96 20 66 42 43 39 27 25 28 33 32 27 28 29 (4X) 11 24 44 23 21 37 49 20 22 113 21 23 49 12 19 17 98 12 9 9 97 10 7 11 13 14 5 4 3 15 16 8 5 2 18 7 13 14 10 15 16 18 1 6 3 11 26 27 28 29 101 11 30 31 33 89 90 22 41 103 37 38 38 26 * No. 14-46-0715 Band saw shim service kit available, not shown 5 2 1 FIG.
PAGE 4
52 50 56 59 72 61 LUBRICATION: Use Type ‘J’ Grease, No. 49-08-4220 Place approx. 1.75 oz. (5 gm) of grease on the 2nd Bevel Pinion (60) and Bevel Spur Gear (61). Place approx. 1.75 oz. (5 gm) of grease on and around the 3rd Gear. Place approx. 1.75 oz. (5 gm) of grease on the Armature Pinion and 1st Gear (58). 57 SCREW TORQUE CHART ITEM 1 7 8 11 12 18 22 31 34 35 36 37 41 43 55 73 74 79 81 87 89 PART NO.
PAGE 5
WIRING INSTRUCTIONSFrom Terminal Block Assembly 2 3 4 1 2 1 3 4 LED SWITCH BOX = WIRE TRAPS PC BOARD 3 TERMINAL BLOCK ASSY. 4 2 4 SWITCH 1 BRUSH CARD ASSEMBLY 2 1 3 C2 C1 AS AN AID TO REASSEMBLY, TAKE NOTICE OF WIRE ROUTING AND POSITION IN WIRE GUIDES AND TRAPS WHILE DISMANTLING TOOL. BE CAREFUL AND AVOID PINCHING WIRES BETWEEN HANDLE HALVES WHEN ASSEMBLING. WIRING SPECIFICATIONS Wire No.
PAGE 6
WIRING INSTRUCTIONSTo Switch Wire #2 is a component of the Terminal Block Assembly. See page 4 for wire routing and trapping. 16 2 14 16 14 15 15 16 15 2 14 LED SWITCH BOX 14 16 = WIRE TRAPS TERMINAL BLOCK ASSY. PC BOARD 16 SWITCH 14 15 15 2 BRUSH CARD ASSEMBLY C2 C1 AS AN AID TO REASSEMBLY, TAKE NOTICE OF WIRE ROUTING AND POSITION IN WIRE GUIDES AND TRAPS WHILE DISMANTLING TOOL. BE CAREFUL AND AVOID PINCHING WIRES BETWEEN HANDLE HALVES WHEN ASSEMBLING. WIRING SPECIFICATIONS Wire No.
PAGE 7
AS AN AID TO REASSEMBLY, TAKE NOTICE OF WIRE ROUTING AND POSITION IN WIRE GUIDES AND TRAPS WHILE DISMANTLING TOOL. WIRING INSTRUCTIONSFrom PC Board and Brush Card Assembly 7 BE CAREFUL AND AVOID PINCHING WIRES BETWEEN HANDLE HALVES WHEN ASSEMBLING. 6 5 8 5 8 10 11 9 7 22-56-0150 Wire Nut (C1 & C2) Brush Card Assy.
PAGE 8
AS AN AID TO REASSEMBLY, TAKE NOTICE OF WIRE ROUTING AND POSITION IN WIRE GUIDES AND TRAPS WHILE DISMANTLING TOOL. WIRING INSTRUCTIONSAll wire routings and trapping 8 BE CAREFUL AND AVOID PINCHING WIRES BETWEEN HANDLE HALVES WHEN ASSEMBLING. 5 16 10 PC BOARDBACK SIDE 14 3 9 15 11 LED SWITCH BOX 4 7 1 = WIRE TRAPS PC BOARD SWITCH TERMINAL BLOCK ASSEMBLY BRUSH CARD ASSEMBLY C2 C1 LED WIRING SPECIFICATIONS Wire No.