Service Parts List

MILWAUKEE ELECTRIC TOOL CORPORATION
13135 W. Lisbon Road, Brookeld, WI 53005
Drwg. 1
BULLETIN NO.
54-40-2635
SERVICE PARTS LIST
FIG. PART NO. DESCRIPTION OF PART NO. REQ.
1 06-75-1012 Left Hand Blade Screw (1)
2 43-34-0795 Outer Blade Flange (1)
3 05-78-1005 M3.5 x 12mm Pan Hd. Phillips Screw (1)
4 49-90-4001 Dust Chute (1)
5 05-78-5316 M4 x 14mm Pan Hd. Tapt. T-20 Screw (3)
6 28-20-2001 Upper Guard Cover (1)
7 06-82-5314 10-24 x 1/2" Pan Hd. Tapt. T-25 Screw (2)
8 44-10-1008 Lower Guard Lever (1)
9 43-34-0790 Inner Blade Flange (1)
10 34-60-0860 Retaining Ring (1)
11 28-41-1001 Lower Guard (1)
12 45-04-0485 10-32 x 13/16" Bumper Screw (1)
13 42-38-0224 Rubber Bumper (1)
14 06-82-5285 6-32 x 1/2" Pan Hd. Taptite T-15 Screw (12)
15 31-15-0265 Spindle/LED Cover (1)
16 22-06-2732 LED Assembly (1)
17 40-50-0045 Lower Guard Spring (1)
18 44-66-0398 Retaining Plate (1)
19 45-14-0015 Plastic Sleeve (1)
25 06-75-5860 1/4-20 x 3/4" Hex Hd. Screw (1)
26 44-60-0741 Pivot Pin (1)
27 45-06-0720 Felt Seal (1)
28 40-50-8046 Spindle Lock Spring (1)
29 44-20-0653 Spindle Lock Plate (1)
30 42-42-1030 Spindle Lock Button (1)
32 --------------- Shoe (1)
33 06-10-4001 M6 x 28mm Carriage Bolt (1)
CATALOG NO. 2631-20
REVISED BULLETIN
SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS
M18 Brushless 7-1/4" Circular Saw
STARTING
SERIAL NO.
DATE
June 2018
WIRING INSTRUCTION
J74A
EXAMPLE:
Component Parts (Small #)
Are Included When Ordering
The Assembly (Large #).
0
00
SEE PAGE TWO
FIG. PART NO. DESCRIPTION OF PART NO. REQ.
34 45-88-1560 Washer (1)
35 43-98-0731 Bevel Adjustment Knob (1)
36 40-50-0650 Spring (1)
37 43-98-0721 Rip Fence Knob (1)
38 34-40-0360 O-Ring (1)
39 02-04-0795 Ball Bearing (1)
40 34-60-0610 Retaining Ring (1)
41 --------------- Rotor (1)
42 02-04-0034 Ball Bearing (1)
49 --------------- Motor Insulator-Bottom (1)
50 --------------- Motor Insulator-Top (1)
51 22-56-0150 Close End Connector (1)
52 23-94-2731 Wire Assy. (Not Shown), see page 2 (1)
53 06-82-1080 M3.0 x 14mm Pan Hd. T-10 ST Screw (6)
55 31-44-1001 Housing Support - Right Housing Halve (1)
57 42-42-0345 Switch Lock-Out Button (1)
58 40-50-1760 Switch Lock-Out Spring (1)
59 05-78-1010 M3.5 x 12mm Pan Hd. T-10 Screw (4)
62 23-66-2635 On-O󰀨 Switch (1)
63 --------------- Housing Cover - Left Housing Halve (1)
64 06-82-7470 6-19 x 11/16" Pan Hd. Plastite T-15 Scr. (10)
65 45-88-1515 Washer (1)
66 45-08-0395 Depth Shaft (1)
67 44-10-0018 Depth Lever (1)
FIG. PART NO. DESCRIPTION OF PART NO. REQ.
68 34-40-4480 O-Ring (1)
69 49-96-0600 3/16" Hex Key (1)
70 --------------- Saw Hook Bar (1)
71 44-60-0585 Coiled Spring Pin (2)
72 45-22-1005 Detent Sleeve (1)
73 40-50-0985 Saw Hook Spring (1)
74 --------------- Saw Hook Housing (1)
75 06-82-0052 M6 x 32mm Pan Hd. T-25 PT Screw (2)
80 23-38-2840 Diode Assembly (1)
81 14-20-5001 Electronic Assembly (1)
82 28-14-9005 Upper Guard Gear Case Assy. w/ Needle Bearing (1)
83 38-50-0160 Output Shaft Assembly (1)
84 23-16-9001 Motor Insulator Assembly (1)
85 14-36-0001 Saw Hook Assembly (1)
86 23-40-6001 Rotor Assembly (1)
87 14-74-1001 Shoe Assembly (1)
88 12-20-8450 Service Nameplate (Not Shown) (1)
89 49-22-2731 Rip Fence (Not Shown) (1)
90 50-55-3550 Contractors Bag (1)
91 14-38-3001 Housing Assembly (1)
92 10-20-0359 Warning Label (Not Shown) (1)
NOTE: Functionally check Lower Guard #11,
with saw set at full depth of cut and 0° bevel.
Place saw upside down with Shoe horizontal.
Fully retract Guard and then release it.
The Guard must return briskly.
71
72
74
70
73
75
80
62
57 58
51
55
68
32
59
(4x)
65 66
69
33
37
36
35
34
26
14(4x) 50
81
49
53
(6x)
30
38
39
40
41
42
27
25
19
17
6
10
5(3x)
9
2
1
4
3
7
8
11
14
(2x)
18
83 14(4x) 28 29
14(2x) 16
15 12 13 82
49 50
53
84
70 71 72
73 74
85
39 40
41 42
86
32 33 34
35 36 37
87
63 64(10x) 67 7
55 63 64
68 88
91
90
LUBRICATION NOTES ON PAGE 3