Service Parts List S/N E55A

59
35
25
27
28
36
43
63
37
34
38
42
50
(9x)
46
(2x)
47
60
28 43 46
47 48 50
62
27 34
35 36
58
44
45
49
44
45
24
19(2x)
11b
12
61
24
57
9
3
2
65
2 3
11b
56
9 25
57
IMPORTANT NOTE: Gearcase end cap #25 is
LEFT HAND THREAD!
As an aid to assembly,
carefully lower the complete
front end of tool (gearcase /
impacting system) onto the
gearcase end cap. Gently
hand tighten front end
assembly onto gearcase
end cap. Be careful not
to cross-thread! Once
installed by hand, seat
gearcase end cap with a
9/16” open end wrench
using light pressure.
Do not over tighten!
LEFT HAND THREAD
good adjustable wrench
1
2
NOTE: Components of the impacting
assembly (61) can drop out of the
gearcase (57). Care must be taken
to hold those elements in
place when assembling
onto the gearcase end
cap (25).
66
59
60
MILWAUKEE ELECTRIC TOOL CORPORATION
13135 W. Lisbon Road, Brookfi eld, WI 53005
Drwg. 6
BULLETIN NO.
54-26-2630
SERVICE PARTS LIST
FIG. PART NO. DESCRIPTION OF PART NO. REQ.
2 34-40-1885 O-Ring (1)
3 44-90-1050 Friction Ring (1)
9 45-88-2653 Plastic Washer (1)
11b --------------- 3/8" Square Anvil (1)
12 02-02-1300 5mm Steel Ball (1)
19 02-02-0180 4.7mm Steel Ball (2)
24 --------------- Ring Gear (1)
25 44-66-2653 Gearcase End Cap with Ball Bearing (1)
27 --------------- Stator Assembly (1)
28 45-30-2653 Rubber Slug (4)
34 --------------- PCBA (1)
35 23-66-2653 On-Off Switch (1)
36 --------------- Terminal Block Assembly (1)
37 45-24-2653 Fwd/Rev Shuttle (1)
38 40-50-1135 Spring (1)
42 40-50-1090 Spring (1)
43 --------------- Left Handle Halve (1)
44 --------------- Belt Hook (1)
45 06-82-0130 6-32 x 5/16" Pan Hd. T-15 Machine Scr (1)
46 06-82-2653 M3.5 x 8mm Pan Hd. Plastite Screw (2)
47 --------------- Right Handle Halve (1)
48 12-20-2653 Service Nameplate (Not Shown) (1)
49 42-55-2653 Carrying Case (1)
50 06-82-7236 4-20 x 5/8" Pan Hd. Plastite T-10 Scr (9)
56 14-30-2656 Gearcase Assembly (1)
57 28-50-2654 Front Gearcase (1)
58 42-70-2653 Belt Clip Assembly (1)
CATALOG NO. 2654-20
REVISED BULLETIN
SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS
M18 FUEL™ 3/8" Square Impact Wrench
STARTING
SERIAL NO.
DATE
Mar. 2015
WIRING INSTRUCTION
E55A
EXAMPLE:
Component Parts (Small #)
Are Included When Ordering
The Assembly (Large #).
0
00
SEE PAGE 2
FIG. LUBRICATION
(Type 'J' Grease, No. 49-08-4220):
11b Lightly coat front washer surface of anvil (11b) with grease.
24,61 Lightly coat the I.D. of the ring gear (24) and the center of
the planet gears of impacting assembly with grease.
57 Coat inside of bushing inside front gearcase with grease.
59 Coat pinion of rotor assembly (59) with grease.
Rubber Boot
No. 49-16-2754
(Optional)
For model
series 2654
and 2655
= 14-20-2654
Electronics Assy.
Assembly going ob-
solete. Replaced by:
FIG. PART NO. DESCRIPTION OF PART NO. REQ.
59 --------------- Rotor Assembly (1)
60 --------------- Handle Assembly (1)
61 14-30-0090 Impacting Assembly (1)
62 14-20-2653 Electronics Assembly (1)
63 45-24-2655 Speed Selector (1)
65 42-06-0025 3/8" Square Anvil Assembly (1)
66 14-46-2654 Rotor/Handle Kit (1)