Service Parts List S/N E56C
MILWAUKEE TOOL
l
www.milwaukeetool.com
13135 W. LISBON RD., BROOKFIELD, WI 53005
Drwg. 3
BULLETIN NO.
54-26-2642
SERVICE PARTS LIST
FIG. PART NO. DESCRIPTION OF PART NO. REQ.
2 44-60-0597 Detent Pin (1)
3 40-50-0925 Detent Spring (1)
4 44-60-0465 Pivot Pin (1)
9 45-88-2653 Plastic Washer (1)
11c --------------- 1/2" Square Anvil (1)
12 02-02-1300 5mm Steel Ball (1)
19 02-02-0180 4.7mm Steel Ball (2)
24 --------------- Ring Gear (1)
25 44-66-2653 Gearcase End Cap with Ball Bearing (1)
27 --------------- Stator Assembly (1)
28 45-30-2653 Rubber Slug (4)
34 --------------- PCBA (1)
35 23-66-2653 On-OSwitch (1)
36 --------------- Terminal Block Assembly (1)
37 45-24-2653 Fwd/Rev Shuttle (1)
38 40-50-1135 Spring (1)
42 40-50-1090 Spring (1)
43 --------------- Left Handle Halve (1)
44 --------------- Belt Hook (1)
45 06-82-0130 6-32 x 5/16" Pan Hd. T-15 Machine Scr (1)
46 06-82-2653 M3.5 x 8mm Pan Hd. Plastite Screw (2)
47 --------------- Right Handle Halve (1)
48 12-20-2653 Service Nameplate (Not Shown) (1)
49 42-55-2653 Carrying Case (1)
50 06-82-7236 4-20 x 5/8" Pan Hd. Plastite T-10 Scr (9)
56 14-30-2656 Gearcase Assembly (1)
57 28-50-2654 Front Gearcase (1)
CATALOG NO. 2655-20
REVISED BULLETIN
54-26-2641
SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS
M18 FUEL™ 1/2" Square Impact Wrench
STARTING
SERIAL NO.
DATE
Jan. 2020
WIRING INSTRUCTION
E56C
EXAMPLE:
Component Parts (Small #)
Are Included When Ordering
The Assembly (Large #).
0
00
SEE PAGE 2
FIG. LUBRICATION
(Type 'J' Grease, No. 49-08-4220):
11c Lightly coat front washer surface of anvil (11c) with grease.
24,61 Lightly coat the I.D. of the ring gear (24) and the center of
the planet gears of impacting assembly with grease.
57 Coat inside of bushing inside front gearcase with grease.
59 Coat pinion of rotor assembly (59) with grease.
«
= Part number change from
previous service parts list.
«
Rubber Boot
No. 49-16-2754
(Optional)
For model
series 2654
and 2655
= 14-20-2656
Electronics Assy.
Assembly going ob-
solete. Replaced by:
FIG. PART NO. DESCRIPTION OF PART NO. REQ.
58 42-70-2653 Belt Clip Assembly (1)
59 16-07-2674 Rotor Assembly (1)
60 31-44-2670 Handle Assembly (1)
61 14-30-0095 Impacting Assembly (1)
62 14-20-2655 Electronics Assembly (1)
63 45-24-2655 Speed Selector (1)
66 42-06-0040 1/2" Square Anvil Assembly (1)
70 23-94-2115 U-Shaped Stamping/Wire Kit (Page 2) (1)
59
35
25
27
28
36
43
63
37
34
38
42
50
(9x)
46
(2x)
47
60
28 43 46
47 48 50
62
27 34
35 36
56
9 25
57
58
44
45
49
44
45
24
11c
12
61
24
57
9
3
2
19(2x)
66
2 3
4 11c
4
IMPORTANT NOTE: Gearcase end cap #25 is
LEFT HAND THREAD!
As an aid to assembly,
carefully lower the complete
front end of tool (gearcase /
impacting system) onto the
gearcase end cap. Gently
hand tighten front end
assembly onto gearcase
end cap. Be careful not
to cross-thread! Once
installed by hand, seat
gearcase end cap with a
good adjustable wrench
using light pressure.
Do not over tighten!
LEFT HAND THREAD
1
2
The original anvil
design shown here is
no longer available.
#66 Anvil Assembly
(42-06-0040)
must be
ordered
instead.
NOTE: Components of the impacting
assembly (61) can drop out of the
gearcase (57). Care must be
taken to hold those elements
in place when assembling
onto the gearcase end
cap (25).
67
59
60