Service Parts List S/N F03D

MILWAUKEE ELECTRIC TOOL CORPORATION
13135 W. Lisbon Road, Brookfi eld, WI 53005
Drwg. 1
BULLETIN NO.
54-26-2613
SERVICE PARTS LIST
FIG. PART NO. DESCRIPTION OF PART NO. REQ.
2 44-60-1162 Detent Pin-Ball (1)
3 40-50-0113 Detent Spring (1)
4 44-60-0465 Roller Pin (1)
9 45-88-2653 Plastic Washer (1)
11c --------------- 1/2" Square Anvil (1)
12 02-02-1300 5mm Steel Ball (1)
19 02-02-0180 4.7mm Steel Ball (2)
24 --------------- Ring Gear (1)
25 44-66-2653 Gearcase End Cap with Ball Bearing (1)
27 --------------- Stator Assembly (1)
28 45-30-2653 Rubber Slug (4)
34 --------------- PCBA (1)
35 23-66-2653 On-Off Switch (1)
36 --------------- Terminal Block Assembly (1)
37 45-24-2653 Fwd/Rev Shuttle (1)
38 40-50-1135 Spring (1)
42 40-50-1090 Spring (1)
43 --------------- Left Handle Halve (1)
44 --------------- Belt Hook (1)
45 06-82-0130 6-32 x 5/16" Pan Hd. T-15 Machine Scr (1)
46 06-82-2653 M3.5 x 8mm Pan Hd. Plastite Screw (2)
47 --------------- Right Handle Halve (1)
48 12-20-2653 Service Nameplate (Not Shown) (1)
49 42-55-2653 Carrying Case (1)
50 06-82-7236 4-20 x 5/8" Pan Hd. Plastite T-10 Scr (9)
56 14-30-2656 Gearcase Assembly (1)
57 28-50-2654 Front Gearcase (1)
CATALOG NO. 2655B-20
REVISED BULLETIN
54-26-2612
SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS
M18 FUEL™ 1/2" Square Impact Wrench
STARTING
SERIAL NO.
DATE
Mar. 2016
WIRING INSTRUCTION
F03D
EXAMPLE:
Component Parts (Small #)
Are Included When Ordering
The Assembly (Large #).
0
00
SEE PAGE 2
FIG. PART NO. DESCRIPTION OF PART NO. REQ.
58 42-70-2653 Belt Clip Assembly (1)
59 16-07-2674 Rotor Assembly (1)
60 31-44-2670 Handle Assembly (1)
61 14-30-0095 Impacting Assembly (1)
62 14-20-2656 Electronics Assembly (1)
63 45-24-2655 Speed Selector (1)
66 42-06-0045 1/2" Sq. Anvil Assy. w/detent pin-ball (1)
70 23-94-2115 U-Shaped Stamping/Wire Kit (Page 2) (1)
FIG. LUBRICATION
(Type 'J' Grease, No. 49-08-4220):
11c Lightly coat front washer surface of anvil (11c) with grease.
24,61 Lightly coat the I.D. of the ring gear (24) and the center of
the planet gears of impacting assembly with grease.
57 Coat inside of bushing inside front gearcase with grease.
59 Coat pinion of rotor assembly (59) with grease.
59
35
25
27
28
36
43
63
37
34
38
42
50
(9x)
46
(2x)
47
60
28 43 46
47 48 50
62
27 34
35 36
56
9 25
57
58
44
45
49
44
45
24
11c
12
61
24
57
9
3
2
19(2x)
66
2 3
4 11c
4
IMPORTANT NOTE: Gearcase end cap #25 is
LEFT HAND THREAD!
As an aid to assembly,
carefully lower the complete
front end of tool (gearcase /
impacting system) onto the
gearcase end cap. Gently
hand tighten front end
assembly onto gearcase
end cap. Be careful not
to cross-thread! Once
installed by hand, seat
gearcase end cap with a
good adjustable wrench
using light pressure.
Do not over tighten!
LEFT HAND THREAD
1
2
The original anvil
design shown here is
no longer available.
#66 Anvil Assembly
(42-06-0045)
must be
ordered
instead.
NOTE: Components of the impacting
assembly (61) can drop out of the
gearcase (57). Care must be
taken to hold those elements
in place when assembling
onto the gearcase
end cap (25).


= Part number change
from previous service
parts list.
