Replacement Part List

M18™ FUEL™ HEDGE TRIMMER
2726-20
H34A
54-49-2700
See Page 3
Aug. 2016
REVISED BULLETIN
SERVICE PARTS LIST
BULLETIN NO.
WIRING INSTRUCTION
DATE
SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS
CATALOG NO.
STARTING
SERIAL NO.
EXAMPLE:
Component Parts (Small #)
Are Included When Ordering
The Assembly (Large #).
0
00
FIG. PART NO. DESCRIPTION OF PART NO. REQ.
1 42-26-0023 24" Blade Assembly 1
2 42-40-0019 Bushing 2
3 05-75-0012 M5 x 0.8 x 30, 4mm Hex Cap Screw 2
4 --------------- Hand Guard 1
5 43-62-0016 Bail Handle 1
6 31-15-0032 Gear Case Cover 1
7 05-88-1210 M4 x 0.7 x 14 Pan Hd. T-20 Machine Screw 16
8 42-92-0009 Gear Cover 1
12a 42-86-0101 Connecting Plate 1
12b 42-86-0101 Connecting Plate 1
23 --------------- Right Motor Housing Insulator - Support 1
24 --------------- Left Motor Housing Insulator - Cover 1
25 06-82-3006 M4 x 1.4 x 18 Pan Hd. ST T-20 Security Scr 4
26 14-20-0036 Electronic Assembly 1
26a --------------- Battery Connector Block Assembly 1
26b --------------- Switch Assembly 1
26c --------------- PCBA 1
26d --------------- Stator Assembly 1
28 40-50-4520 Lock-Off Spring 1
29 05-74-0480 M5 x 0.8 x 25, 4mm Hex Cap Screw 2
30 42-42-0011 Lock-Off Button 1
31 31-92-0016 Switch Trigger 1
32 --------------- Right Housing Assembly - Cover 1
33 --------------- Left Housing Assembly - Support 1
34 05-88-1200 M4 x 1.4 x 16 Pan Hd. ST T-15 Screw 8
MILWAUKEE TOOL
l
www.milwaukeetool.com
13135 W. Lisbon Road, Brookeld, WI 53005
Drwg. 1
32
26a
31
30
33
26b
7
(4x)
26c
26d
4
24
25(4x)
35
45
43
12a
12b
8
6
7
(6x)
36
2
(2x)
3
(2x)
5
1
7
(4x)
34
(8x)
29
(2x)
23
26
26a 26b
26c 26d
40
32
33
44
4
37
37
42
23
24
7(2x)
38
28
FIG. PART NO. DESCRIPTION OF PART NO. REQ.
35 49-62-0010 Blade Sheath 1
36 12-20-0086 Service Nameplate 1
37 10-20-1041 Caution Label 1
38 45-06-0026 Felt Seal 1
40 31-44-2726 Housing Kit 1
42 31-50-2712 Motor Insulator Kit 1
43 14-29-0011 Gear / Crank Shaft Assembly 1
44 43-54-0099 Hand Guard Kit 1
45 14-30-0011 Gear Case / Rotor Assembly 1
FIG. NOTE:
5 Dimples of Bail Handle (5) must face to the front of the tool.
26d Be sure to position the grooves in the Stator Assembly (26b) on
the ribs in the inside cavities of Motor Insulator Halves (23,24).
38 See page two for proper location and orientation of Felt Seal (38).
44 Hand Guard Kit (44) must be installed prior to Housing Kit (40)
being secured with screws (29).
45 Do not attempt to remove the rotor from the Gear Case /
Rotor Assembly (45).
SCREW TORQUE SPECIFICATIONS
SEAT TORQUE
FIG. PART NO. WHERE USED (KG/CM) (IN/LBS)
3 05-75-0012 Blade Assembly 26 22.57
7 05-88-1210 Gear Case Cover 10 8.68
7 05-88-1210 Bail Handle 10 8.68
7 05-88-1210 Hand Guard 10 8.68
7 05-88-1210 Motor Insulator 10 8.68
25 06-82-3006 Motor Insulator 13 11.28
29 05-74-0480 Housing Halves 30 26.04
34 05-88-1200 Housing Halves 17 14.76