Replacement Part List

FIG. PART NO. DESCRIPTION OF PART NO. REQ.
8 06-82-5004 M5 x 16mm Pan Hd. ST T-25 Screw (11)
9 --------------- Handle Cover (1)
10 14-20-2001 Electronics Assembly (1)
11 06-82-1087 M3 x 12mm Pan Hd. ST T-10 Screw (3)
12 42-52-3001 Oil Cap Assembly (1)
12d 34-40-9002 Oil Cap O-Ring (1)
13 43-44-4001 Gasket (1)
14 45-66-3001 Oil Tank (1)
15 10-20-2078 Spanish/French Warning Label (1)
17 34-40-4002 O-Ring (1)
18 42-86-0001 Connector (1)
19 23-66-9001 Micro Switch (1)
20 34-60-0750 Retaining E-Ring (1)
21 05-88-1200 M4 x 16mm Pan Hd. ST T-20 Screw (3)
22 40-50-9220 Cone Spring (1)
23 45-76-3001 Inlet Tube (1)
24 16-01-6001 Rotor Assembly (1)
24b 45-06-2001 Seal Pad (1)
24c 40-50-9225 Oil Pump Spring (1)
25 05-78-5316 M4 x 14mm Pan Hd. ST T-20 Screw (10)
26 42-92-8001 Dust Cover (1)
27 42-54-7002 Oil Pump Assembly (1)
28 45-06-1001 Seal Ring (1)
29 45-88-0406 Washer (1)
30 14-30-3001 Gear Case Assy. with Needle Bearing (1)
30a 34-40-0029 Retaining Ring (1)
30b 02-04-0001 Ball Bearing (1)
32 32-60-3002 Spur Pinion (1)
33 05-55-1001 M6 Hex Nut (1)
34 --------------- Handle Support (1)
41 44-66-9001 Wrench Catcher (1)
42 45-96-1001 Wrench (1)
43 42-92-3001 Wire Cover (1)
44 14-73-7001 Spindle/Gear Assembly (1)
45 45-76-2001 Outlet Tube (1)
46 40-50-6010 Switch Spring (1)
47 42-42-4001 Lock O󰀨 Button (1)
48 45-72-3001 Trigger (1)
49 45-60-9001 Switch Support (1)
50 12-20-2727 Service Nameplate (1)
68 45-88-0506 Washer (1)
95 14-34-0220 Handle Kit (1)
FIG. NOTES
24 Great care must be used when removing or installing rotor
assembly. Magnet on rear end of rotor is very fragile.
33 Torque hex nut to 100kg.cm±3 (87in.lbs±2).
95 Prior to taking tool apart, use a sharp razor blade to score the
center line of nameplate (33) and symbol labels (36 and 37).
This will allow housing halves (15 and 29) to separate when
housing screws are removed.
15,39, A clean, dry surface is essential for proper performance for any
50 adhesive system. The area intended for application of any ad-
hesive label or nameplate must be prepared by cleaning with
isopropyl alcohol. The solvent is to be applied with a clean, lint
free applicator and the surface allowed to dry before applying
any label or nameplate.
24b
25
(2x)
27
29
30a
30b
32
33
44
45
43
21
22
34
19
20
18
11
(2x)
23
25
(4x)
17
48
47
46
41
42
12d
13
14
11
25
(4x)
10
9
50 8
(10x)
49
21
(2x)
12d
12
24c
28
26
15
8 9 34
15 50
95
30a
30b
30
24b
24c
24
68