Replacement Part List

LUBRICATION NOTES:
Type ‘J’ Grease, No. 49-08-4220
When installing Gearcase Cover Kit (126),
place 4.8 g, (.16 oz) grease to the Bevel
Gear (79). Place 6 g (.21 oz.) to the large
Spur Gear (80). Coat all of the gear teeth
on small Spur Gear (81) with grease.
Coat Washer (58) and ends of shafts
(82 & 85) with J Grease.
LUBRICATION NOTES:
Type ‘Y’ Grease,
No. 49-08-5270
Lightly coat both sides of
Washers (89) and Clutch
Plates (88) with Y Grease.
74
73
75
71
68
1
69
1
2
91
90
89
88
87
8
85
1
84
83
80
58
70
100
30
68
78
77
76
72
86
30 68
70
128
73 74 75
76 77 78
136
71 72 73 74
75 76 77 78
127
98 99
100
137
71 72 73 74
75 76 77 78
127
58 59 79 80 81
82 83 84 85
126
99
98
79
82
81
59
7
8
3
26
Dowel
To properly tighten
hex head screw (3), use
a wooden dowel or a nylon
rod in the opening between
the rear pulley (7) and gearcase
(26). Be careful not to damage
pulley tire (8). Apply enough pressure
to prevent rear pulley from turning.
Torque hex head screw (3) to 312 in/lbs.
Service Tool 61-30-6232 can be ordered
to secure rear pulley to tighten hex hd. screw.
Service Tool
61-30-6232
Use screws (1) to temp-
orarily attach service
tool to rear pulley. Hold
tool and tighted hex
head screw (3) to 312 in/lbs.
FIG. PART NO. DESCRIPTION OF PART NO. REQ.
1 06-82-5314 10-24 x 1/2" Pan Hd. Tapt. T25 (11 of 23) (23)
2 31-15-0325 Pulley Cover (1 of 2) (2)
8 45-69-0010 Pulley Tire (1 of 2) (2)
30 --------------- Pin (1 of 2) (2)
58 45-88-0406 Washer (1 of 2) (2)
59 02-04-0175 Ball Bearing (1 of 2) (2)
68 --------------- Gearcase (1)
69 31-15-0330 Rear Pulley Shroud (1)
70 --------------- Needle Bearing (2 of 3) (3)
71 --------------- Rear Roller Block (1)
72 06-82-5574 10-24 x 7/8" Pan Hd. Tapt. T-25 (2 of 4) (4)
73 --------------- Pin (1 of 2) (2)
74 --------------- Ball Bearing (1 of 2) (2)
75 --------------- Washer (2 of 4) (4)
76 --------------- Ball Bearing (4 of 8) (8)
77 --------------- Washer (2 of 4) (4)
78 --------------- 12-24 UNC x .96" Slotted (2 of 4) (4)
79 --------------- Bevel Gear (1)
80 --------------- Spur Gear (1)
81 --------------- Spur Gear (1)
82 --------------- Shaft (1)
FIG. PART NO. DESCRIPTION OF PART NO. REQ.
83 --------------- Ball Bearing (1)
84 --------------- Gearcase Cover (1)
85 --------------- Spindle (1)
86 45-88-1580 Washer (1)
87 28-95-2700 Rear Pulley (1)
88 43-06-0015 Clutch Plate (2)
89 43-06-0010 Clutch Washer (2)
90 40-50-0805 Disc Spring (1)
91 06-75-0010 M Screw, 3/8"-16 UNC 5/8" Hex Hd. (1)
98 06-82-5346 8-32 x 3/4" Pan Hd. Taptite T-20 (2)
99 --------------- Tire Cleaning Brush Cover (1)
100 --------------- Tire Cleaning Brush (1)
126 14-29-0057 Gearcase Cover Kit (1)
127 42-28-0025 Rear Guide Roller Kit (1)
128 14-30-0038 Gearcase Top Assembly (1)
136 14-46-0465 Guide Roller Kit (1)
137 44-60-0295 Tire Clearing Brush Kit (1)
NOTE:
312 in/lbs.
or 26 ft/lbs.
SCREW TORQUE CHART
Torque
Fig. Part No. Location (In/Lbs.)
10 06-81-0075 Support Plate 36
15 06-75-0035 Support Plate 104
24 06-82-5376 Gearcase
Pulley Support 38
26 06-82-7252 LED Cover 22
28 06-75-4675 Front T-Handle 83
36 06-82-5360 Handle Cover
Support Handle 39
40 06-82-7270 Handle Cover 17
61 06-82-7326 Diaphragm 16
72 06-82-5574 Front Roller Block
Rear Roller Block 39
91 06-75-0010 Rear Pulley 312
93 06-82-5330 T-Block 19
97 06-82-0065 T-Block 19
98 06-82-5346
Tire Cleaning Brush Cover 22
104 06-82-8828 Bearing Plate
Ground Terminal 17
106 06-82-5358 Diaphragm 38
109 05-81-0010 LED Assembly 6
150 06-82-0145 Release Lever 22