Use and Care Manual

FIG. PART NO. DESCRIPTION OF PART NO REQ.
52 06-82-0072 M5 x 20mm Pan Hd. Sems T-25 Screw (4)
53 45-88-0008 Washer (1)
67 --------------- Spring Pin (1)
157 45-88-0047 Washer (1)
181 06-82-0103 M3 x 6mm ST Screw (1)
191 06-82-0108 M5 x 10mm Pan Hd. T-25 Mach. Screw (15)
192 42-92-0021 Cloth Dust Cover-2 (1)
193 05-89-0012 M6 x 13mm CH Mach. Screw, S5 (1)
194 06-55-0008 M8 Hex Nut with Nylon (1)
195 43-98-0019 Height Adjustment Knob (1)
196 45-94-0011 Height Adjustment Disk (1)
197 06-55-0012 M6 Hex Nut with Nylon (3)
198 --------------- Height Adjustment Handle Shaft (1)
199 34-40-0106 O-Ring (1)
200 34-60-0019 E-Ring (1)
201 45-88-0048 Washer (2)
202 45-88-0049 Wave Washer (1)
4
= Type ‘Y’ Grease, 49-08-5270
LUBRICATION:
198 Apply a light film of grease to the
Height Adjustment Handle Shaft
as shown prior to installing onto
Dust Collection Casting.
204 Apply a liberal amount of grease
to Height Adjustment Bevel Gear-1
being sure to coat all of the teeth.
205 Apply a liberal amount of grease to the Height Adjustment Bevel
Gear-2, being sure to coat all of the teeth.
210 Apply a light coat of grease to the threads and shaft of the Height
Adjustment Screw.
212 Place a light film of grease to entire Height Adjustment Shaft-A.
213 Place a light film of grease to entire Height Adjustment Shaft-B.
220 Place a light coat of grease to the contact areas within the channel
of the Front Bevel Mechanism.
223 Place a light coat of grease to the contact areas within the channel
of the Back Bevel Mechanism.
NOTE:
When servicing gears
or gearcase, 90-95%
of old grease must be
removed prior to new grease
being added. Clean gear ass-
emblies with clean, dry cloth.
211
(6x)
181
191
(5x)
253
192
195
193
157
194
196
197
67
198
199
200
201
(2x)
202
203
204
197
(2x)
211
210
52
(4x)
209
(2x)
208
212
206
205
207
(2x)
214
(2x)
215
213
224
191
(2x)
223
221
(4x)
219
(4x)
218
(4x)
217
(4x)
220
191
(3x)
216
225
226
53
227
228
222
231
(2x)
191
(4x)
191
229
230
232
235
(3x)
234
(3x)
233
67
198
281
DUST COLLECTION ASSEMBLY
FIG. PART NO. DESCRIPTION OF PART NO REQ.
203 45-88-0051 Washer (1)
204 32-05-0012 Height Adjustment Bevel Gear-1 (1)
205 32-05-0013 Height Adjustment Bevel Gear-2 (1)
206 42-28-0011 Height Adjustment Block (1)
207 06-75-0027 M5 x 24mm Cap Hd. Sems Screw, S4 (2)
208 45-88-0059 Wave Washer (1)
209 45-88-0060 Washer (1)
210 45-04-0011 Height Adjustment Screw (1)
211 06-82-0111 M5 x 10mm Pan Hd. T-25 Sems Screw (7)
212 45-08-0011 Height Adjustment Shaft-A (1)
213 45-08-0012 Height Adjustment Shaft-B (1)
214 06-82-0113 M4 x 12mm Pan Hd. T-20 Mach. Screw (2)
215 42-92-0023 Riving Knife Dust Cover (1)
216 42-92-0022 Front Dust Cover (1)
217 06-82-0107 M6 x 14mm Pan Hd. T-25 Mach. Screw (4)
218 05-91-0010 External Tooth Spring Washer (4)
219 44-60-0092 Spring Pin (4)
220 14-04-0005 Front Bevel Mechanism Assembly (1)
221 06-75-0031 M6 x 21.5mm Cap Hd. Sems, S5 (4)
222 28-50-0011 Dust Collection Casting (1)
223 14-04-0035 Back Bevel Mechanism Assembly (1)
224 42-92-0024 Back Dust Cover (1)
225 06-82-0109 M5 x 13mm Pan Hd. Sems T-25 Screw (1)
226 31-44-0122 Bevel Handle (1)
227 45-88-0065 Washer (1)
228 05-77-0011 M10 x 25mm Hex Machine Screw, M5 (1)
229 44-72-0015 Bevel Indicator (1)
230 05-91-0015 External Tooth Spring Washer (1)
231 44-66-0068 Dust Cloth Insert Plate (2)
232 42-92-0026 Cloth Dust Cover-1 (1)
233 42-92-0027 Dust Collection Cover (1)
234 05-77-0012 M5 x 16mm Wing Screw (3)
235 06-75-0029 M5 x 18mm Cap Hd. Mach. Screw, S4 (3)
253 44-66-0069 Dust Cloth Insert Plate-2 (1)
281 45-08-0013 Height Adjustment Handle Shaft Assy. (1)