Use and Care Manual

3
• When battery pack is not in use, keep it away
from other metal objects, like paper clips, coins,
keys, nails, screws or other small metal objects,
that can make a connection from one terminal to
another. Shorting the battery terminals together may
cause burns or a re.
• Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact ac-
cidentally occurs, ush with water. If liquid con-
tacts eyes, additionally seek medical help. Liquid
ejected from the battery may cause irritation or burns.
• Do not use a battery pack or tool that is dam-
aged or modied. Damaged or modied batteries
may exhibit unpredictable behavior resulting in re,
explosion or risk of injury.
• Do not expose a battery pack or tool to re or
excessive temperature. Exposure to re or tem-
perature above 265°F (130°C) may cause explosion.
• Follow all charging instructions and do not
charge the battery pack or tool outside the
temperature range specied in the instructions.
Charging improperly or at temperatures outside the
specied range may damage the battery and increase
the risk of re.
SERVICE
• Have your power tool serviced by a qualied
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
• Never service damaged battery packs. Service
of battery packs should only be performed by the
manufacturer or authorized service providers.
SPECIFIC SAFETY RULES FOR
IMPACT WRENCHES
• Hold power tool by insulated gripping surfaces,
when performing an operation where the fastener
may contact hidden wiring. Fasteners contacting
a “live” wire may make exposed metal parts of the
power tool “live” and could give the operator an electric
shock.
• Wear ear protectors when impact drilling. Expo-
sure to noise can cause hearing loss.
• Use only sockets and other accessories speci-
cally designed for use on impact wrenches and
drivers. Other sockets and accessories might shatter
or break causing injury.
• Maintain labels and nameplates. These carry im
-
portant information. If unreadable or missing, contact
a MILWAUKEE service facility for a free replacement.
•
WARNING
Some dust created by power sanding,
sawing, grinding, drilling, and other
construction activities contains chemicals known to
cause cancer, birth defects or other reproductive
harm. Some examples of these chemicals are:
• lead from lead-based paint
• crystalline silica from bricks and cement and other
masonry products, and
• arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on
how often you do this type of work. To reduce your
exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such
as those dust masks that are specially designed to
lter out microscopic particles.
SYMBOLOGY
Volts
Direct Current
No Load Revolutions per Minute (RPM)
Impacts per Minute Under Load (IPM)
C
US
UL Listing for
Canada and U.S.
SPECIFICATIONS
Volts .............................................................. 18 DC
Battery Type .................................................M18™
Charger Type ................................................M18™
Cat. No. ..................................................... 2762-20
Anvil Type ...................................... 1/2" Square-Pin
RPM ...................Mode 1...................Speed 0-1200
Mode 2...................Speed 0-1700
IPM ....................Mode 1....................Impacts 1700
Mode 2....................Impacts 2300
Cat. No. ..................................................... 2763-20
Anvil Type .................................... 1/2" Square-Ring
RPM ...................Mode 1.....................Speed 0-425
Mode 2...................Speed 0-1700
IPM ....................Mode 1......................Impacts 450
Mode 2....................Impacts 2300
Cat. No. ..................................................... 2764-20
Anvil Type .................................... 3/4" Square-Ring
RPM ...................Mode 1...................Speed 0-1200
Mode 2...................Speed 0-1700
IPM ....................Mode 1....................Impacts 1700
Mode 2....................Impacts 2300
Cat. No. ..................................................... 2765-20
Anvil Type ................................................7/16" Hex
RPM ...................Mode 1...................Speed 0-1200
Mode 2...................Speed 0-1700
IPM ....................Mode 1....................Impacts 1700
Mode 2....................Impacts 2300
FUNCTIONAL DESCRIPTION
1. 1/2" Square drive anvil with pin
(2762-20)
2. LED
3. Control switch
4. Trigger
5. 2-Mode drive control
6. Handle
7. 1/2" Square drive anvil with ring (2763-20)
8. 3/4" Square drive anvil with ring (2764-20)
9. 7/16" Hex Quick Connect (2765-20)
1
2
4
5
3
9
7
8
6