Replacement Part List

ManualsBrandsMilwaukee ManualsLawn MowersM18 FUEL 18V Cordless Mower, Dual Blower, String Trimmer, (4) QUIK-LOK Attachments, (5) 12.0 Ah Batteries, (2) Charger

BULLETIN NO.

SERVICE PARTS LIST

54-QC-2823

Apr. 2022

REVISED BULLETIN

DATE

WIRING INSTRUCTION

See Pages 6, 7 & 8

M44A

STARTING

SERIAL NO.

2823-20

CATALOG NO.

M18 FUEL™ 21" Self-Propelled Dual Battery Mower

SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS

EXAMPLE:

Component Parts (Small #) Are Included

When Ordering The Assembly (Large #).

MILWAUKEE TOOL

www.milwaukeetool.com

13135 W. Lisbon Road, Brookeld, WI 53005

Drwg. 1

HANDLE BAR / CONTROLS PAGE 4

FRONT WHEELS / DECK PAGE 2

REAR WHEELS / DECK PAGE 3

WIRING INSTRUCTIONS PAGES 6,7,8

SCREW TORQUE CHART / SVC NOTES PAGE 5

Service for this Milwaukee Tool FUEL Product

Please Call: 1-833-953-2010

CONNECTOR HOT MELT PROCEDURE PAGE 9

Summary of content (9 pages)

PAGE 1
BULLETIN NO. SERVICE PARTS LIST 54-QC-2823 SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS 00 0 M18 FUEL™ 21" Self-Propelled Dual Battery Mower STARTING CATALOG NO. M44A 2823-20 SERIAL NO. EXAMPLE: Component Parts (Small #) Are Included When Ordering The Assembly (Large #). FRONT WHEELS / DECK PAGE 2 REAR WHEELS / DECK PAGE 3 HANDLE BAR / CONTROLS PAGE 4 REVISED BULLETIN DATE Apr.
PAGE 2
11 1 2b 3 4 9 210 10 11 13 14 15 16 17 18 144 147 10 17(2x) 1 18(4x) 9 2b(6x) 147 144 3 (2x) 13 14 4 15 19 16(2x) 2b (4x) 6 7 FIG. 29 30 31 32 33 34 36 37 38 39 41 42 43 44 45 46 47 48 49 PART NO.
PAGE 3
FIG. 35b 40 43 47 48 60 62 63 64a 65 66 67 68 69 PART NO. 05-74-0241 ----------------------------45-94-0084 05-55-0158 ------------------------------------------05-78-5311 ----------------------------05-81-0266 ----------------------------- DESCRIPTION OF PART NO. REQ. M8 x 16mm Pan Hd. T-40 Mach. Screw (10) Deck Height Adjustment Spring (1) Mower Deck (1) Plastic Wheel Cap (2) M10 Hex Nut with Nylon Insert (2) Height Adjustment Linkage Weldment (1) Rear Wheel Assembly (2) Wheel Gear (2) M5 x 18mm Pan Hd.
PAGE 4
FIG. 102 103 104 105 106 107 109 110 111 112 113 114 115 118 212 213 218 PART NO. 22-44-0010 ----------------------------------------------------------------------31-94-0024 05-74-0244 ----------------------------31-44-0174 05-74-0102 43-98-0307 45-88-0279 ------------------------------------------- DESCRIPTION OF PART NO. REQ.
PAGE 5
SCREW TORQUE SPECIFICATIONS FIG. PART NO. DESCRIPTION OF FASTENER 2b --------------M4 x 16mm Pan Hd. Taptite T-20 Screw 2b --------------M4 x 16mm Pan Hd. Taptite T-20 Screw 2b --------------M4 x 16mm Pan Hd. Taptite T-20 Screw 2b --------------M4 x 16mm Pan Hd. Taptite T-20 Screw 2b --------------M4 x 16mm Pan Hd. Taptite T-20 Screw 2b --------------M4 x 16mm Pan Hd. Taptite T-20 Screw 2c --------------M4 x 16mm Pan Hd. Taptite T-20 Screw 2c --------------M4 x 16mm Pan Hd.
PAGE 6
Wire Routing for Switch Cable Cable Clip Cable Clip Cable Clip Switch Cable Secure the Switch Cable with three Cable Clips, as shown. 3/16” Wire Clip Handlebar Mounting Bracket Rectangular Opening Secure the Switch Cable with Wire Clip as shown. Route Switch Cable through the rectangulat opening of the Handlebar Mounting Bracket. Switch Cable Plug the connector of the Switch Cable into connector from the Main PCBA. Secure Switch Cable with a Cord Clamp and two screws.
PAGE 7
Wire Routing for Front LED Lights and Blade Motor LED Light Wire Clip & Screw Wire Tie LED Light Hole Route wires for the front LED lights as shown. Be sure to place wires completely in the bottom of all wire traps. Secure front LED light wires with 12 wire clips and screws. Route wires from front LED lights and blade motor through hole here. Fasten wires together with wire tie.
PAGE 8
Wire Routing for Main PCBA Sensor Small PCB plate Make sure that no wire crosses over this blue wire when fastening the small PCB plate. SEE NEXT PAGE FOR LUBRICATION AND HOT MELT GLUE APPLICATION PROCESSES RELATING TO THIS CONNECTOR Join this Connector to the Switch Connector Before plugging connectors, orient and place the sensor in the area shown. Place the connectors for the lights and motors on the side of the PCBA boat shown.
PAGE 9
PROCEDURAL OVERVIEW Surface prep and glue Metal must be in contact with skin. Grounding Clip Equipment 1. Sure Bonder (PRO9700A) Adjustable Temp Glue Gun 2. Element HMS707 (Hot Melt Glue) 3. Cleaning Pads 4. Isopropyl Alcohol 5. ESD Bracelet Technician must stand on mat. ESD Bracelet Procedure ESD Protection must be worn in this station. 1. Sure Bonder (PRO9700A) Adjustable Temp Glue Gun Settings: • Temperature Setting is 320°F. • Trigger Pull is set to Full Stroke (Approx. 1”). 2.