Replacement Parts List

ManualsBrandsMilwaukee ManualsImpact WrenchesM18 Fuel 3/8" Compact Impact Wrench w/ Friction Ring Kit

(4x)

(5x)

(2x)

(4x)

39 40 41

42 50

6 7

NOTE:

Route wires of the TRI-LED Lighting Assembly

through wire traps on the side of Front Gearcase.

Place a piece of Kapton tape or something similar

over the wires/traps to secure on gearcase.

BULLETIN NO.

54-26-3000

SERVICE PARTS LIST

FIG. PART NO. DESCRIPTION OF PART NO. REQ.

3 05-88-1257 M4 x 22mm Pan Hd. T-20 ST Screw (4)

6 44-90-1050 3/8" Friction Ring (1)

7 34-40-1885 O-Ring (1)

8 --------------- 3/8" Anvil (1)

29 34-40-8005 O-Ring (1)

39 --------------- Right Housing Halve-Cover (1)

40 --------------- Left Housing Halve-Support (1)

41 06-82-6351 M3 x 16mm Pan Hd. ST T-10 Screw (9)

42 06-82-2367 M3 x 38mm Pan Hd. ST T-10 Screw (2)

44 --------------- Belt Hook (1)

45 06-82-2500 6-32 x 7mm Pan Hd. Tapt. T-15 Screw (1)

49 45-24-0031 Forward/Reverse Shuttle (1)

50 12-20-0253 Service Nameplate (1)

53 45-88-2554 Front Gearcase Washer (1)

54 28-50-2854

Front Gearcase Assy. with TRI-LED Lighting

(1)

60 31-44-2854 Housing Service Kit (1)

61 16-01-2854 Rotor/Back Cap Assembly (1)

62 14-20-2854 Electronics Assembly (1)

63 44-66-2854 End Cap Assembly (1)

64 14-30-2854 Impacting Assembly (1)

65 42-70-0950 Belt Clip Kit (1)

66 45-24-2854 Speed Selector Assembly (1)

67 42-06-2854 3/8" Square Anvil Assy. w/ Friction Ring (1)

CATALOG NO. 2854-20

REVISED BULLETIN

SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS

M18™ FUEL™ 3/8" Compact Impact Wrench w/ Friction Ring

STARTING

SERIAL NO.

WIRING INSTRUCTION

L57A

EXAMPLE:

Component Parts (Small #)

Are Included When Ordering

The Assembly (Large #).

MILWAUKEE TOOL

www.milwaukeetool.com

13135 W. Lisbon Road, Brookeld, Wisc. 53005

Drwg. 1

FIG. PART NO. DESCRIPTION OF PART NO. REQ.

70 49-16-2854 Rubber Boot (Accessory) (1)

71 42-55-0067 Blow Molded Carrying Case (1)

SCREW TORQUE SPECIFICATIONS

SEAT TORQUE

FIG. PART NO. WHERE USED (KG/CM) (IN/LBS)

3 05-88-1255 Front Gearcase 21±2 18±2

41 06-82-6351 Right Housing Halve 10±1 8±1

41 06-82-6351 Rotor/Back Cap Assy. 7±1 6±1

42 06-82-2367 Right Housing Halve 10±1 8±1

45 06-82-2500 Belt Hook 16±2 14±2

See Pages 3 & 4

DATE

Aug. 2020

Summary of content (4 pages)

PAGE 1
BULLETIN NO. SERVICE PARTS LIST SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS 54-26-3000 REVISED BULLETIN M18™ FUEL™ 3/8" Compact Impact Wrench w/ Friction Ring CATALOG NO. 00 EXAMPLE: 0 Component Parts (Small #) Are Included When Ordering The Assembly (Large #). STARTING SERIAL NO. 2854-20 DATE Aug. 2020 WIRING INSTRUCTION L57A See Pages 3 & 4 50 41 (5x) 40 41 60 39 42 50 39 42 (2x) 71 41 (4x) 63 29 61 62 70 40 49 67 6 7 8 29 66 45 64 44 8 7 6 54 3 (4x) FIG.
PAGE 2
1 1 3 2 1 1 LUBRICATION Use Type 'J' Grease, No. 49-08-4220 (16 oz. tub) NOTE: When servicing, remove 90-95% of the existing grease prior to installing Type ‘J’. Original grease may be similar in color but not compatible with ‘J’. Clean gear assemblies with a clean, dry cloth. NOTE Regarding parts to be lubricated: 1 Apply a light coating of grease to these parts. 2 Apply a liberal amount of grease to these parts. 3 Place 1.3g of grease to hammer cavity of impacting system.
PAGE 3
1 3 5 2 4 6 1. Place potting boat assembly in left handle halve. Assemble the battery terminal block and mode selector into the corresponding cavities in handle halve. 2. Place high voltage ring terminal over the screw boss as shown. Route ground wire through the traps/channels in handle halves being sure wire is seated completely to the bottom. 3. Install the on-off switch over the ground wire and into cavity in handle halve. Be sure on-off switch is seated firmly and squarely in position. 4.
PAGE 4
7 8 9 7. Install stator to the rear of the handle halve. Place stator wires in handle halve cavity, behind on-off switch in the following order from bottom to top: gray, purple and black. Be sure stator is firmly and squarely in handle cavity and that stator wires are pushed completely down below the top edge of handle. 8. Check that all electrical and mechanical components are properly in place in handle halve. Be sure there are no interferences creating pinched wires. 9.