Cut Sheet
FIG. PART NO. DESCRIPTION OF PART NO. REQ.
1 48-32-3065 Magnetic Bit Holder (1)
8 02-80-0055 Thrust Bearing (1)
17 40-50-0132 Bit Retaining Spring (1)
18 02-02-0130 9/64" Steel Ball (1)
20 45-88-0204 Thrust Bearing Washer (1)
21 40-50-0142 Conical Spring (1)
FIG. PART NO. DESCRIPTION OF PART NO. REQ.
22 42-70-0222 Drive Clutch (1)
25 02-04-0640 Ball Bearing (1)
26 44-60-0412 Pin (1)
28 --------------- Screwdriver Bit (1)
29 02-04-0033 Ball Bearing (1)
31 02-04-0701 Ball Bearing (1)
32 34-60-0575 Retaining Ring (1)
33 31-15-0022 Lock-On Slide Lever (1)
34 40-50-0422 Lock-On Spring (1)
35 --------------- Right Housing Halve-Housing Cover (1)
36 06-82-1080 M3 x 14mm Pan Hd. ST T-10 Screw (15)
40 40-50-1090 Terminal Block Spring (1)
44 --------------- Auto Start Button (1)
45 --------------- Auto Start Plate (1)
47 --------------- Left Housing Halve-Housing Support (1)
48 42-70-0059 Belt Clip Kit (1)
49 06-82-0130 6-32 x 5/16" Pan Hd. T-15 Mach. Scr. (1)
50 06-82-0013 M3 x 38mm Pan Hd. ST T-10 Screw (1)
51 12-20-0101 Service Nameplate (1)
54 34-40-0076 O-Ring (1)
60 31-44-1086 Housing Set (1)
61 14-20-2866 Electronics Assembly
Consisting of:
Stator, Main PCBA, On-Off Switch,
LED, Mode Selector PCBA and
Battery Connector Block (1)
62 32-10-0057 Clutch Gear Assembly (1)
63 16-07-0212 Rotor Assembly (1)
64 28-14-0711 Rear Gearcase Assembly (1)
65 28-14-0712 Front Gearcase Assembly (1)
66 49-26-1090 Nosecone Assembly (1)
67 42-66-0025 Clutch Chuck Assembly (1)
68 45-24-0305 Auto Start Assembly (1)
69 42-55-2866 FUEL™ Small Contractor Bag (1)
10-20-1048
French/Spanish Warning Label (Not Shown)
(1)
WIRING INSTRUCTION
REVISED BULLETIN DATE
SERVICE PARTS LIST
BULLETIN NO.
STARTING
SERIAL NO.
54-42-0020
See Page 2
SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS
2866-20
CATALOG NO.
M18™ FUEL™ DRYWALL SCREWDRIVER
Oct. 2016
H47A
EXAMPLE:
Component Parts (Small #) Are Included
When Ordering The Assembly (Large #).
00
0
32
31
26
25
36
(4x)
62
17
18
8
20
21
22
51
47
49
49
48
25
54
64
61
29
33
34
44
45
65
36
(3x)
66
28
1
35
36
(8x)
50
40
35 47
51
60
44
45
68
29 31
32
63
17
18
67
54
Back Side
facing #62
Front Side
facing #67
22
MILWAUKEE TOOL
l
www.milwaukeetool.com
13135 W. LISBON RD., BROOKFIELD, WI 53005
Drwg. 1
LUBRICATION NOTE:
When servicing this tool, 90-95% of the old
grease must be removed prior to new grease being added.
LUBRICATION
(Type "Y" Grease, No. 49-08-5270)
• Place a light coat of grease in the bottom inside cavity of rear
gearcase (64) and over ball bearing (25). Use about .5 grams.
• Fill the 3 enlarged clutch pockets of the clutch gear assembly (62)
with .5 grams grease. Install drive clutch (22).
• Add approximately 4.3 grams of grease into the rear gearcase,
around the teeth of the armature pinion and the teeth of the clutch
gear. Place a heavy coat of grease over the drive clutch (22).
• Coat with grease the thrust bearing (8), thrust bearing washer (20)
and conical spring (21).
• Applyalightlmofgreasetotheleadchamferandbarrelofthe
clutch chuck (67) prior to assembly into front gearcase (65).
• With clutch chuck (67) installed in the front gearcase (65), add ap-
proximately 3 grams of grease over the lugged surfaces of clutch
chuck.
69