M18 Impact Driver Replacement Parts List

BULLETIN NO.
54-26-2880
SERVICE PARTS LIST
FIG. PART NO. DESCRIPTION OF PART NO. REQ.
1 --------------- Front Gear Case (1)
2 45-88-2653 Front Gear Case Washer (1)
3 42-76-0019 Sleeve (1)
4 34-60-0005 Retaining Ring (1)
5 45-88-2026 Washer (1)
6 40-50-0056 Spring (1)
7 02-02-1100 Steel Ball (1)
8 40-50-0057 Spring (1)
9 45-88-1547 Washer (1)
10 42-06-2800 Anvil (1)
24 34-40-0595 O-Ring (1)
33 06-82-2367 M3 x 38mm Pan Hd. ST T-10 Screw (2)
34 06-82-6351 M3 x 16mm Pan Hd. ST T-10 Screw (7)
35 --------------- Right Handle Halve - Cover (1)
36 45-24-0260 Shuttle (1)
37 23-28-0400 LED Lens (1)
38 --------------- Speed Selector (1)
39 --------------- Shuttle (1)
40 40-50-0027 Spring Plate (1)
41 --------------- Left Handle Halve - Support (1)
43 --------------- Belt Clip (1)
44 06-82-2500 6-32 x 5/16 Slt. Pan Hd. T-15 Mach. Sc. (1)
45 14-30-2800 Gearcase/Anvil Assembly (1)
46 14-30-2805 Gear Box Impacting Assembly (1)
47 44-66-2680 End Cap Assembly (1)
48 14-20-2820 Electronics Assembly (1)
48a --------------- Hall Sensor PCBA (1)
48b --------------- Battery Terminal Connector Block (1)
 48c --------------- On-O󰀨Switch (1)
48d --------------- Stator/Main PCBA (1)
CATALOG NO. 2851-20
REVISED BULLETIN
SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS
M18™ Brushless 1/4" Hex Impact Driver (3 Speed)
STARTING
SERIAL NO.
DATE
May 2019
WIRING INSTRUCTION
J56A
See Pages 2 & 3
EXAMPLE:
Component Parts (Small #)
Are Included When Ordering
The Assembly (Large #).
0
00
MILWAUKEE TOOL
l
www.milwaukeetool.com
13135W.LisbonRoad,Brookeld,Wisc.53005
Drwg. 2
FIG. PART NO. DESCRIPTION OF PART NO. REQ.
49 16-01-2830 Rotor Assembly (1)
50 31-44-2864 Handle Housing Kit (1)
51 42-70-0950 Belt Clip Kit (1)
52 45-24-1300 Speed Selector Kit (1)
60 12-20-4107 Service Nameplate (1)
61 42-55-4002 Carrying Case, Optional Equipment (1)
62 10-20-4107 Warning Label (Not Shown) (1)
61
4
8
9
1
2
10
7
46
24
37
38
39
40
48a
48b
5
6
3
43
44
60
35
33
(2x)
34
(7x)
48c
36
48d
41
49
43
44
51
35 41
60
50
24
47
48a 48b
48c 48d
48
38 39
40
52
1 2 3 4 5
6 7 8 9 10
45
FIG. LUBRICATION
Use Type 'J' Grease, No. 49-08-4220 (1 lb. can)
Service grease may not be compatable with grease used
during manufacturing. 90-95% of the old grease must be
removed prior to any new grease being added.
10 Lightly coat front washer surface of anvil with grease,
place a dab in the ball cavities of anvil.
45 Coat inside of bushing inside front gearcase with grease.
46 NOTE: Do not wash impact assembly. Use a clean, dry cloth
to wipe away any excess grease or contamination.
46 Lightly coat the I.D. of the ring gear and the center of the
planet gears of impacting assembly with grease.
49 Coat pinion of rotor assembly with grease.