Replacement Parts List

BULLETIN NO.
54-26-4000
SERVICE PARTS LIST
FIG. PART NO. DESCRIPTION OF PART NO. REQ.
1 06-82-2368 M3.5 x 16mm Pan Hd. ST T-10 Screw (9)
10 43-44-7037 Gasket (1)
24 34-40-1885 O-Ring, 3/8" Anvil (1)
25 44-90-1050 Friction Ring, 3/8" Anvil (1)
FIG. PART NO. DESCRIPTION OF PART NO. REQ.
34 06-82-2366 M5 x 26.5mm Pan Hd. ST T-25 Screw (4)
37 06-82-2367 M3 x 38mm Pan Hd. ST T-10 Screw (2)
38 42-42-2735 Forward/Reverse Shuttle (1)
39 --------------- Right Housing Halve-Cover (1)
40 --------------- Left Housing Halve-Support (1)
44 12-20-9100 Service Nameplate (1)
46 06-82-2500 6-32 x 7mm Pan Hd T-15 Screw (1)
47 --------------- Belt Hook (1)
48 --------------- Tether Stamping (1)
49 --------------- Tether Ring (1)
55 16-01-3040 Rotor Assembly (1)
56 31-44-7007 Housing Kit (1)
57 14-20-5020 Electronics Assembly, 3/8" (1)
58 44-66-2675 End Cap Assembly (1)
59 32-65-0385 Ring Gear (1)
60 14-30-2960 Hammer Assembly, 3/8" Anvil (1)
62 42-06-2960 Anvil Assembly, 3/8" (1)
65 42-70-0950 Belt Clip Kit (1)
66 45-24-2854 Mode Selector Assembly (1)
67 42-55-6375 Blow Molded Carrying Case (1)
68 49-16-2960 Rubber Boot, Accessory (1)
69 28-50-2960 Gearcase Assembly, 3/8" Anvil (1)
71 49-16-2962 Tether Ring Kit, Accessory (1)
CATALOG NO. 2960-20
REVISED BULLETIN
SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS
M18™ FUEL™ 3/8" Mid Torque Impact Wrench w/ Friction Ring
STARTING
SERIAL
DATE
Aug. 2020
WIRING INSTRUCTION
L78A
SEE PAGE 2
EXAMPLE:
Component Parts (Small #)
Are Included When Ordering
The Assembly (Large #).
0
00
MILWAUKEE TOOL
l
www.milwaukeetool.com
13135 W. Lisbon Road, Brookeld, Wisc. 53005
Drwg. 1
24
25
69
60
59
10
58
57
66
38
55
40
1
(4x)
34
(4x)
62
24
25
44
1
(5x)
39
37
(2x)
49
48
71
48
49
65
46
47
47 46
56
1 37 39
40 44
67
68
LUBRICATION NOTES:
Type ‘J’ Grease
No. 49-08-4220, 1 lb. can
NOTE: When servicing, remove 90-95% of the existing grease prior
to installing Type ‘J’. Original grease may be similar in
color but not compatible with ‘J’. Prior to reinstalling,
clean gear assemblies with a clean, dry cloth.
Lightly coat all parts highlighted here with
‘J’ grease. Apply a greater amount
of grease to all internal and
external gear teeth.
NOTE:
Service Hammer
Assembly (60)
comes completely
pre-lubricated.
Do not attempt to
disassemble.
Model 2960-20
shown