Operator’s Manual

3
• When battery pack is not in use, keep it away
from other metal objects, like paper clips, coins,
keys, nails, screws or other small metal objects,
that can make a connection from one terminal
to another. Shorting the battery terminals together
may cause burns or a re.
• Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact ac-
cidentally occurs, flush with water. If liquid
contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irritation
or burns.
• Do not use a battery pack or tool that is dam-
aged or modied. Damaged or modied batteries
may exhibit unpredictable behavior resulting in re,
explosion or risk of injury.
• Do not expose a battery pack or tool to re or
excessive temperature. Exposure to re or tem-
perature above 265°F (130°C) may cause explosion.
• Follow all charging instructions and do not charge
the battery pack or tool outside the temperature
range specied in the instructions. Charging
improperly or at temperatures outside the specied
range may damage the battery and increase the risk
of re.
SERVICE
• Have your power tool serviced by a qualied
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
• Never service damaged battery packs. Service
of battery packs should only be performed by the
manufacturer or authorized service providers.
SPECIFIC SAFETY RULES FOR
UTILITY CRIMPER
• Use tool only as directed. Only trained personnel
should operate tool.
•
WARNING
To reduce the risk of arc ash,
electric shock and property
damage, work on deenergized lines when
possible. Tool is not insulated. Should work
on energized lines be required, ensure all proper
precautions, including those contained in NFPA
70E, have been taken rst.
• Do not use tool without crimping jaws installed.
Fingers could be crushed.
• Keep hands away from crimping jaws while tool
is in use. Fingers could be crushed.
• To reduce the risk of injury, wear safety goggles
or glasses with side shields when operating or
servicing the tool.
• Inspect and discard workpieces with cracks or
wear before use. Materials may crack or shatter.
• Use tool only with MILWAUKEE crimping jaws,
dies, and connectors for which they are rated.
Jaws, dies, and connectors must be used in an
APPROVED COMBINATION to achieve a success-
ful operation. Improper combinations can result in
a faulty crimp. Electric shock, re, explosion, and
property damage could occur.
• Follow connector manufacturers' installation
instructions. Other uses may cause damage to
the tool, accessories, and workpiece.
• If using with a lanyard, do not exceed maximum
capacity marked on the lanyard label. Always
determine the weight of the product, with all ac-
cessories, when selecting the appropriate lanyard
system. Exceeding maximum capacity may result in
serious injury. See specications for tool and battery
weight.
• Use only with energy absorbing lanyards that
comply with ANSI/ISEA 121. Ropes, straps or
chains may break and cause failure. Do not use
with lanyards at full tension.
• Always use common sense and be cautious when
using tools. It is not possible to anticipate every
situation that could result in a dangerous outcome.
Do not use this tool if you do not understand these
operating instructions or you feel the work is beyond
your capability; contact Milwaukee Tool or a trained
professional for additional information or training.
• Maintain labels and nameplates. These carry
important information. If unreadable or missing,
contact a MILWAUKEE service facility for a free
replacement.
•
WARNING
Some dust created by power sanding,
sawing, grinding, drilling, and other
construction activities contains chemicals known to
cause cancer, birth defects or other reproductive
harm. Some examples of these chemicals are:
• lead from lead-based paint
• crystalline silica from bricks and cement and other
masonry products, and
• arsenic and chromium from chemically-treated
lumber.
Your risk from these exposures varies, depending on
how often you do this type of work. To reduce your
exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such
as those dust masks that are specially designed to
lter out microscopic particles.
SYMBOLOGY
Volts
Direct Current
WARNING
To reduce the risk of arc
ash, electric shock and
property damage, work on deenergized
lines when possible. Tool is not insulated.
Should work on energized lines be re-
quired, ensure all proper precautions, in-
cluding those contained in NFPA 70E,
have been taken rst.
WARNING
Keep hands away from
crimping jaws while tool is
in use. Fingers could be crushed.
To reduce the risk of injury, wear safety
goggles or glasses with side shields when
operating or servicing the tool.
Read operator's manual
C
US
UL Listing for Canada and U.S.