Use and Care Manual
BULLETIN NO.
54-24-5010
SERVICE PARTS LIST
FIG. PART NO. DESCRIPTION OF PART NO. REQ.
1 05-88-0019 M8.0 x 1 LH T-40 Chuck Screw (1)
2 42-66-1006 1/2” Keyless Chuck (1)
13 06-82-7336 M4 x 20mm Pan Hd. ST T-10 Screw (4)
14 06-82-7337 M4 x 20mm Washer Pan Hd. ST T-10 Scr. (4)
16 42-42-3001 Forward/Reverse Shuttle (1)
17 45-24-1045 Speed Change Lever (1)
19 --------------- Left Housing Halve - Support (1)
20 --------------- Belt Clip (1)
21 06-82-2500 6-32 x 7mm Pan Hd. Taptite T-15 Screw (2)
31 --------------- Secondary Clamp Body (1)
32 --------------- Primary Clamp Body (1)
33 --------------- Threaded Side Handle (1)
34 44-10-4002 Speed Selector Slide (1)
35 40-50-9001 Detent Spring (1)
36 --------------- Right Housing Halve - Cover (1)
38 --------------- Bit Holder with Clip (1)
39 06-82-6350 M3 x 16mm Pan Hd. ST T-10 Screw (5)
FIG. PART NO. DESCRIPTION OF PART NO. REQ.
40 06-82-2367 M3 x 38mm Pan Hd. ST T-10 Screw (2)
43 12-20-0478 Service Nameplate (1)
50 43-72-0950 Bit Holder Assembly (1)
51 31-44-1004 Housing Assembly (1)
52 42-70-0950 Belt Clip Assembly (1)
53 14-29-1014 Gearbox Assembly (1)
54 16-07-1016 Rotor/End Cap Assembly (1)
55 14-20-1120 Electronics Assembly (1)
56 42-62-1002 Side Handle Assembly (1)
57 42-55-9005 Blow Molded Carrying Case (1)
10-20-1048 Warning Label (Not Shown) (1)
CATALOG NO. 2804-20
REVISED BULLETIN
SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS
M18™ FUEL™ Brushless Hammer-Drill
STARTING
SERIAL NO.
DATE
Aug. 2018
WIRING INSTRUCTION
J77A
EXAMPLE:
Component Parts (Small #) Are Included
When Ordering The Assembly (Large #).
0
00
SEE PAGE 2
MILWAUKEE TOOL
l
www.milwaukeetool.com
13135 W. Lisbon Road, Brookeld, Wisc. 53005
Drwg. 3
54
13
(4x)
36
43
39
(5x)
38
21 40(2x)
55
16
31
34
17
35
32
33
53
14
(4x)
2
1
19
20
21
20
21
52
20
38
50
31 32
33
56
19 36 39
40 43
51
SEE INSTRUCTIONS
BELOW ON HOW TO
REMOVE THE CHUCK
SCREW AND CHUCK
REMOVING THE CHUCK SCREW:
Set the Speed Selector Slide (34) to the #1 setting.
With the aid of a small pencil tip torch (or use an air reduction nozzle on a heat gun) apply heat
into the chuck opening, directly to the head of reversing screw just prior to removing the screw.
Place a T40 1/4” torx bit into the head of the reversing screw and place a 1/4” boxed end wrench
over the hex on the T40 bit. It is recommended to use a 12”-18” metal tube or pipe as leverage
over the boxed wrench. In a clockwise direction apply a slow, steady force on the ‘cheater bar’
to break the screw loose.
REMOVING THE KEYLESS CHUCK:
Tighten a 1/2” or 10mm Allen Key into the jaws of the chuck. Place
the tool into a vise with soft jaws (this will require that you remove
the belt clip from the tool). It is recommended to use a 12”-18” metal
tube or pipe as leverage over the allen key. In a counter-clockwise
direction apply a slow, steady force on the ‘cheater bar’ to break the
chuck loose.
INSTALLING NEW CHUCK AND SCREW:
Torque Chuck to 1095 kg/cm (950.418 in/lbs or 28.93 ft/lbs)
Torque Screw to 461 kg/cm (400.130 in/lbs or 33.34 ft/lbs)
57