OPERATOR’S MANUAL hose powering system BY BRIGGS & STRATTON Briggs & Stratton Power Products Group, LLC Milwaukee, Wisconsin, U.S.A. Manual No.
Thank you for purchasing this quality-built Amplifi™ Hose Powering System. We are pleased that you’ve placed your confidence in the Amplifi brand. When operated and maintained according to the instructions in this manual, your Amplifi Hose Powering System will provide many years of dependable service. Amplifi Hose Powering Systems are built and serviced proudly by Briggs & Stratton®.
Table of Contents Operator Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Equipment Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Unpack Hose Powering System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Prior to Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operator Safety Equipment Description Read this manual carefully and become familiar with your Hose Powering System. Know its applications, its limitations, and any hazards involved. The Hose Powering System operates at a maximum of 150 PSI and a flow rate of up to 5.2 gallons per minute (19.68 liters per minute). Every effort has been made to ensure that the information in this manual is accurate and current.
WARNING Risk of electrocution. Contacting both power conductors, at the same time could cause electric shock or burn resulting in death or serious injury. • Connect only to a properly grounded outlet. DO NOT remove ground pin from plug. • Inspect cord before each use, DO NOT use if cord is damaged. • Keep all connections dry and off the ground. • DO NOT touch plug with wet hands. • DO NOT run cord through doorways, windows, holes in ceilings, walls, or floors. • DO NOT walk on cord.
Assembly Read entire operator’s manual before you attempt to assemble or operate your new Hose Powering System. Your Hose Powering System requires some assembly but is quickly ready for use. If you have any problems with the assembly of your Hose Powering System, please call the Hose Powering System helpline at (800) 743-4115. Tools Needed • Needle nose pliers. • Phillips screw driver. Items Not Included • Long (100 ft [30.48 m] max.
6. Attach (long) heavy duty discharge garden hose to pump outlet (A) inside hose pot. Tighten by hand. Turn on water and run for 30 seconds to flush system. Turn off water. NOTICE Use Amplifi brand heavy duty garden hose or equivalent with 400 psi minimum burst pressure. A Transporting the Hose Powering System NOTICE Use handle for transporting unit over smooth level surfaces only. For stairs and uneven surfaces, carry unit using assistance. WARNING Lifting hazard.
Features and Controls Read the Operator’s Manual and safety rules before operating your Hose Powering System. Compare the illustrations with your Hose Powering System to familiarize yourself with the locations of various controls and adjustments. Save this original manual for future reference. A K B J C H D G F E A - Warning Label — Identifies hazards to be avoided when using your pressure washer.
Operation 8. Press TEST button (B). The red indicator should disappear. How to Start Your Hose Powering System Follow the instructions below in the order presented. If you have any problems operating your Hose Powering System, please call the Hose Powering System helpline at (800) 743-4115. 1. Using the transporting handle, place Hose Powering System near an outside water source capable of supplying water at a flow rate greater than 6 gallons per minute (22.7 l) and no less than 30 PSI (2.
How to Use the Spray Gun Nozzles Sprayer Removal/Reassembly You should now be familiar with how to START and STOP your Hose Powering System. If not, please refer to the previous section to familiarize yourself with STARTING and STOPPING the system before continuing. The information in this section will instruct you how to adjust the spray pattern and to apply pressure washer safe detergents/ soaps. The selector nozzle allows you to switch between five different spray pattern nozzles.
Other Tips • • • • Hose Powering System Rinsing Water large plant beds with power shower. Use gentle shower for delicate plants or single planters. Power Jet allows max performance on second stories. A short delay for the pump to turn on after the trigger is squeezed is normal. A longer more flexible hose will result in a longer starting delay. Applying Detergent • • • • WARNING Chemical Burn Hazard. Chemicals could cause burns resulting in death, serious injury and/or property damage.
Maintenance General Recommendations Regular maintenance will improve the performance and extend the life of the Hose Powering System. See any authorized dealer for service. The Hose Powering System’s warranty does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, the operator must maintain the Hose Powering System as instructed in this manual, including proper storage.
Winter or Long Term Storage Water should not remain in the unit for long periods of time. Sediments or minerals can deposit on pump parts and “freeze” pump action. Initial Storage Procedures 1. Flush detergent bottle by removing it from spray gun and pouring out all remaining solution. 2. Rinse detergent bottle out with fresh clean water. 3. Run the Hose Powering System with the “Power Jet” high pressure nozzle selected. Flush for one or two minutes. 4.
Troubleshooting Problem Cause Pump has following problems: failure to produce pressure, erratic pressure, chattering, loss of pressure, low water volume. 1. 2. 3. 4. 5. 6. Water inlet is blocked. Inadequate water supply. Inlet hose is kinked or leaking. Clogged inlet hose screen. Water supply is over 100°F (38°C). Discharge hose is blocked or leaks. 7. Nozzle is obstructed. 8. Pump is faulty. 1. Water supply is not turned on. 2. Unit is not turned on. 3. Water pressure is too low.
BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC HOSE POWERING SYSTEM OWNER WARRANTY POLICY Effective January 1, 2011; replaces all undated Warranties and all Warranties dated before January 1, 2011 LIMITED WARRANTY Briggs & Stratton Power Products Group, LLC will repair or replace, free of charge, any part(s) of the hose powering system that is defective in material or workmanship or both. Transportation charges on product submitted for repair or replacement under this warranty must be borne by purchaser.
Amplifi Hose Powering System Product Specifications * * Max Outlet Pressure ..................................................... 150 PSI Flow Rate..................................................................... 5.2 GPM Detergent Mix.......................................... See MFR’s Instructions Water Supply Temperature............... Not to exceed 100°F (38°C) Motor.....................................................................Induction Type Rated Voltage......................................
