OPERATOR'S MANUAL MANUEL de L'UTILISATEUR MANUAL del OPERADOR Catalog No. No de Cat. Catálogo No. 4270-20 ALPHA INDUSTRIAL TOOL & EQUIPMENT 51 Tamarack Drive Thornhill, Ont L3T 4 W2 Canada PH. 905-731-1310 FAX 905-731-1044 COMPACT ELECTROMAGNETIC DRILL PRESS PERCEUSE À COLONNE ÉLECTROMAGNÉTIQUE COMPACTE PRENSA TALADRADORA ELECTROMAGNETICA COMPACTA TO REDUCE THE RISK OF INJURY, USER MUST READ AND UNDERSTAND OPERATOR'S MANUAL.
GENERAL SAFETY RULES FOR ALL POWER TOOLS WARNING! READ ALL INSTRUCTIONS Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. The term "power tool" in all of the warnings listed below refers to your mains-operated (corded) power tool or battery-opearted (cordless) power tool. SAVE THESE INSTRUCTIONS WORK AREA SAFETY 1. Keep work area clean and well lit. Cluttered or dark areas invite accidents. 2.
SPECIFIC SAFETY RULES FOR ELECTROMAGNETIC DRILL PRESS 1. Always use safety strap when drilling overhead or on a vertical surface (see Safety Strap under Operation). Mounting can release. 2. Clean the surface before attaching the drill stand to the work surface. Paint, rust, scale, or uneven surfaces decrease the holding strength of the magnet. Chips, burrs, dirt and other foreign matter on the surface of the magnet base will also decrease holding power. 3.
FUNCTIONAL DESCRIPTION 1. Drill motor 2. Slide 3. Wrench storage 4 4. Stop knob 5. Pinion 6. Hub 7. Handle screw 8. Feed handle 9. Grip 2 1 (includes 3/32" and 3/16" hex keys) 3 6 5 7 10. Housing 8 11. Cord 12. Safety strap 9 13. Magnetic base 14. Spacer 17 15. Drill spindle 16. Support bracket 17. Cutting fluid reservoir 18. Control panel 10 16 11 19. Magnet indicator light 20. Magnet switch 12 21. Drill on/off switch 22.
GROUNDING EXTENSION CORDS WARNING! Improperly connecting the grounding wire can result in the risk of electric shock. Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded. Do not modify the plug provided with the tool. Never remove the grounding prong from the plug. Do not use the tool if the cord or plug is damaged. If damaged, have it repaired by a MILWAUKEE service facility before use.
TOOL ASSEMBLY WARNING! To reduce the risk of injury, always unplug tool before attaching or removing accessories or making adjustments. Use only specifically recommended accessories. Others may be hazardous. Adjusting the Gib Assembly (Fig. 3) Fig. 3 Attaching Feed Handles and Grips (Fig. 1) Fig. 1 1. Assemble the feed handles and grips to the hub. Tighten securely. 2. To mount the hub to either side, align the two (2) dowel pins on the hub with the holes in the pinion. Tighten the handle screw.
OPERATION WARNING! WARNING! To reduce the risk of injury, wear safety goggles or glasses with side shields. To reduce the risk of injury, do not hold workpiece by hand. 5. Typical Operation 1. Check the work surface to make sure it is clean and free of foreign materials. WARNING! Paint, rust, scale or uneven surfaces decrease the holding strength of the magnet. Chips, burrs, dirt and other foreign materials on the surface of the magnetic base will also decrease holding power.
. Start the drill motor by pulling the drill on/off switch to the "ON" position. WARNING! To reduce the risk of injury, always keep hands, rags, clothing, etc. away from moving parts and chips. Do not try to remove chips while the cutter is rotating. Chips are sharp and can pull objects into moving parts (see Fig. 9). Fig. 9 WARNING! Excessive force will break magnet free. 10. Keep constant pressure throughout the entire operation to prevent chips and burrs from falling under the cutting edges.
MAINTENANCE ACCESSORIES WARNING! To reduce the risk of injury, always unplug your tool before performing any maintenance. Never disassemble the tool or try to do any rewiring on the tool's electrical system. Contact a MILWAUKEE service facility for ALL repairs. Maintaining Tools Keep your tool in good repair by adopting a regular maintenance program. Before use, examine the general condition of your tool. Inspect guards, switches, tool cord set and extension cord for damage.
