Service Parts List S/N H93A
6d
7h
(4x)
7n
(12x)
7a
(2x)
7c
(2x)
7k
(4x)
7b
7j
(4x)
7p
(2x)
7d
(8x)
7e/7f
(2 each)
7r(2x)
NOTE:
Outer Strength Plate-Right (7e) has the same
outside configuration as Outer Strength Plate-Left
(7f). The difference between the two plates is that
Outer Strength Plate-Left (7f) does not have a
threaded hole on the top tab.
7b
7q
(2x)
7m
7g
(2x)
5b
5a
7a
7c
5c
(3x)
7b
7r 7d
(2x)
7p
7j
(2x)
14
5a 5b 5c
5d 5e
15
7c
7r
2
2j
When installing a new Work Piece Support Feed Arm Assembly (14),
the following items must be assembled onto Feed Arm (5b):
Hex Socket Cap Screw (5a), End
Bracket (7a), Feed Arm Sleeve
(7c) with Round Plate (7r) and
three Feed Arm Pads (5c).
NOTE:
Legs and other hardware are not
shown for illustration clarity.
4h
7p(2x)
5b
5e
(2x)
5d
4g
(2x)
4a
4d
(2x)
4c
(2x)
4b
4h
4f
4k
(2x)
4e
(2x)
4j
6c
2
2j
2j can be
purchased
at any hard-
ware store.
Consisting of:
M8 x 45mm Cap
Screw w/ 6mm
Socket Hex Drive
M8 Lock Washer
M8 Flat Washer
4d
4c
6
4c 4d 4h
6c 6d
13
4a 4b 4c 4d 4e
4f 4g 4h 4j 4k
12
5d
5e
1a
1f
1e
1b
8
1c
1g
1d
1k
1j
3b
3c
10
1a 1b 1c 1d 1e
1f 1g 1j 1k
11
1a 1c 1d 1e
1f 1g 3b 3c
7b
18
There are three Leg
Assemblies (11)
There is one Leg
Assembly with an
Adjuster (10)
See detail below for exploded
view of Main Body Assy. (7)
7
7a 7b 7c 7d 7e 7f 7g 7h
7j 7k 7m 7n 7p 7q 7r
7
7a 7b 7c 7d 7e 7f 7g 7h
7j 7k 7m 7n 7p 7q 7r
17
7g 7m
7q
16
1a 1c 1d
1f 1g
9
48-08-0551
FOLDING MITER SAW STAND
May 2020
54-40-5460
REVISED BULLETIN
SERVICE PARTS LIST
BULLETIN NO.
WIRING INSTRUCTION
DATE
CATALOG NO.
SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS
SERIAL
NUMBER
EXAMPLE:
Component Parts (Small #) Are Included
When Ordering The Assembly (Large #).
0
00
H93A
NOTE: Fastener quantities shown here are for one end of the Main Body.
For illustration clarity, only one corner (leg area) is depicted.
SEE
PAGE 2
FOR PART
LISTINGS
MILWAUKEE TOOL
l
www.milwaukeetool.com
13135 W. LISBON RD., BROOKFIELD, WI 53005
Drwg. 2