Instructions / Assembly

4
5
Hardware Included
NOTE: Items not shown in actual size. Hardware
lengths are approximate.
Hardware Item Description Quantity
AA Bolt M6 x 16L 10
BB Steel washer 16
CC Bolt M8 x 12L 16
DD Screw M4 x 12L 20
EE Screw M6 x 12L 8
FF Screw M4 x 16L 20
GG Nut M6 2
HH
Shoulder bolt
M6 x 8L
2
II Nylon washer 2
JJ Screw M6 x 16L 2
Item Description Quantity
Side handle 1
Tool hanger 1
6" Swivel caster
with brake
2
6" Rigid caster 2
Bracket 2
Shelf hinge bracket 2
Front bumper 8
Rear bumper 2
Chest corner extrusion 2
Cabinet corner extrusion 2
Cord storage bracket 4
Utility hook 2
Paper towel
holder bracket
2
Paper towel holder rod 1
Bottle opener 1
NOTE: Begin product assembly close to the nal
intended location of your chest/cabinet. This product
is heavy and may be difcult to move after assembly.
Attaching the Side Handle
Attach the side handle to the rolling cabinet using
four bolts (AA). The side handle can be attached to
either side of the rolling cabinet, but must match the
end where the swivel casters are installed.
NOTE: The holes in the cabinet are tapped and do
not require nuts.
AA
Installing the Casters
CAUTION
Two people may be required to
complete installation.
Do not overtighten the screws.
1. Ensure all cabinet drawers are securely locked into
place using the key lock on the rolling cabinet.
2. Lay the rolling cabinet on its back. Use the packag-
ing material to protect the nish.
3. Mount the two swivel casters with brake to the
rolling cabinet using four bolts (CC) and washers
(BB) per caster. The swivel casters with brake
must be installed on the end of the cabinet with
the side handle.
4. Mount the two rigid casters to the opposite end
of the rolling cabinet using four bolts (CC) and
washers (BB) per caster.
5. Tighten all bolts securely with a wrench.
GROUNDING
WARNING
Improperly connecting the ground-
ing wire can result in the risk of
electric shock. Check with a qualied electrician
if you are in doubt as to whether the outlet is
properly grounded. Do not modify the plug pro-
vided with the chest/cabinet. Never remove the
grounding prong from the plug. Do not use the
chest/cabinet if the cord or plug is damaged. If
damaged, have it repaired before use. If the plug
will not t the outlet, have a proper outlet installed
by a qualied electrician.
Chests/Cabinets with Three Prong Plugs
Chests/cabinets marked “Grounding Required”
have a power strip with a three wire cord and three
prong grounding plug. The plug must be connected
to a properly grounded outlet (See Figure A). If the
power strip should electrically malfunction or break
down, grounding provides a low resistance path to
carry electricity away from the user, reducing the risk
of electric shock.
The grounding prong in the plug is connected through
the green wire inside the cord to the grounding sys-
tem in the power strip. The green wire in the cord
must be the only wire connected to the power strip's
grounding system and must never be attached to an
electrically “live” terminal.
Your power strip must be plugged into
Fig. A
an appropriate outlet, properly in-
stalled and grounded in accordance
with all codes and ordinances. The
plug and outlet should look like those
in Figure A.
ASSEMBLY
CAUTION
Be sure to follow the assembly in-
structions for the appropriate
chest/cabinet. Do not use power tools to as-
semble chest/cabinet. Tighten bolts with hand
wrenches.
Tools Required (Not Included)
Phillips
screwdriver
Safety
goggles
10 mm
Wrench
13 mm
Wrench
6. Return the rolling cabinet to its upright position.
BB
CC
NOTE: The casters may come preinstalled. To switch
caster placement, follow steps 1-2 before removing
casters. Remove casters, retain hardware, and then
complete steps 3-6.
Installing the Chest onto the Cabinet
CAUTION
Two people may be required to
complete installation.
1. Place the top chest on top of the rolling cabinet.
NOTE: The holes in the cabinet are tapped and do
not require nuts.
2. Attach the two brackets to the back of the product
to secure the top chest to the rolling cabinet. Place
the brackets over the holes and secure with four
screws (DD) per bracket.
3. Tighten all screws securely with a Phillips screw-
driver.
DD
Installing the Drawer Liners and Mat
Place the drawer liners in appropriately sized draw-
ers and the mat in the chest lid area to protect the
surface.