Instructions / Assembly

ManualsBrandsMilwaukee ManualsBottom Tool Chests46 in. 10-Drawer Roller Cabinet Tool Chest

Installing the Corner Extrusions

and Bumpers

Place the front bumpers on both ends of the extrusion

by sliding the extrusion into the cavity of the bumpers.

Attach the front bumpers with extrusions using two

screws (FF) per bumper.

Attach the two rear bumpers to the back of the lower

cabinet using two screws (FF) per bumper.

Installing the Cord Storage Brackets

Attach the brackets to the back of the chest and

cabinet with two screws (DD) per bracket. Orient the

brackets with one pointed up and one pointed down

so that the power outlet cord can be wrapped around

the brackets for storage.

Installing the Storage Shelf

Attach the shelf hinge brackets to the right cabinet

using two bolts (AA) for each bracket. Attach the

storage shelf to the brackets using one washer (II),

nut (GG) and bolt (HH) on each end.

Installing the Tool Hanger

Attach the tool hanger to the left end of the chest

using two bolts (AA).

Installing the Utility Hooks and

Paper Towel Holder

Attach the utility hooks and paper towel holder to

either end of the chest using two screws (EE) for

each hook and bracket.

Installing the Bottle Opener

Attach the bottle opener to the left side of the cabinet

using two screws (JJ).

Installing the Power Cord

Locate the power cord inside one of the right-hand

drawers. Untie the power cord and gently pull the

cord plug through the grommet.

OPERATION

WARNING

To avoid injury or property damage,

do not exceed maximum shelf ca-

pacity. Use care when moving chest/cabinet on

incline or rough surface. Chest/cabinet may tip

if weight is not evenly distributed front to back

and side to side. Place more than half the total

load weight on the bottom cabinet when possible.

Locking and Unlocking the Chest/Cabinet

NOTE: The drawers must be fully closed before

locking/unlocking the unit.

Insert the key. Turn it fully left to lock, or fully right

to unlock. Always remove the key after locking and

unlocking.

Using the Caster Brakes

To lock the swivel casters, step

down on the levers marked

ON. Be sure to lock both

casters to prevent chest/

cabinet from rolling or swiv-

eling. To unlock casters,

push down on the levers

marked OFF.

Moving the Chest/Cabinet on

an Incline or Rough Surface

Take care that the chest/cabinet does not tip or

become unbalanced when moving it on an incline

or rough surface. Do not exceed an incline of 10

degrees. Lock the chest/cabinet and secure all items

before moving.

Rolling the Chest/Cabinet

The chest/cabinet is only intended for rolling short

distances. Only roll the chest/cabinet using the han-

dle. Do not push or pull chest/cabinet by the frame

or product may tip. Do not modify the chest/cabinet

in any way. Drilling holes or modifying the chest/

cabinet will lower the load capacity, which can cause

the chest/cabinet to collapse, resulting in injury. Lock

the chest/cabinet and secure all items before rolling.

Lifting the Chest/Cabinet

The cabinet and chest/cabinet combo are not

intended to be lifted. However, if you need to lift,

empty the chest/cabinet and then place straps or

forks inside and next to casters. Do not lift loaded

chests/cabinets. Be sure all bystanders are moved

away before lifting chest/cabinet.

Mounting Chargers

The rolling cabinet comes equipped with four pre-

installed charger mounting bosses, located below the

power strip. The charger mounts are suitable for hold-

ing MILWAUKEE M18™ & M12™ Multi Voltage char-

gers as well as M18™ chargers. To mount a charger,

install a screw (DD) into each boss, then slide the

charger's key-hole slots over the screws. Slide the

charger toward the oor to lock it onto the screws.

Removing the Drawers

1. Fully extend and empty the drawer.

2. Depending on the side, either lift or lower the

release lever on both sides so the slides can ride

over the stops. Pull out to remove.

Release Lever

Installing the Drawers

1. Pull the slides and slide carrier out until fully ex-

tended.

2. Hold the slide on the cabinet while aligning it with

the slide on the drawer.

3. Slightly insert one side and repeat for the other

side.

4. Slowly push the drawer until it is fully closed to

engage the slide.

5. Open and close the drawer to verify proper operation.

MAINTENANCE

WARNING

To reduce the risk of injury, contact

MILWAUKEE Corporate After Sales

Service Technical Support for ALL repairs and

replacement parts.

Maintaining the Chest/Cabinet

Keep your chest/cabinet in good repair by adopting a

regular maintenance program. Before use, examine

the general condition of your chest/cabinet. Check for

loose screws, misalignment, binding of wheels, bro-

ken parts and any other condition that may affect its

safe operation. Do not use a damaged chest/cabinet.

Maintaining the Casters

Grease the casters annually using high quality bear-

ing grease.

Grease

Points

Maintaining the Drawers

1. Periodically clean the drawers with a mild deter-

gent and water.

2. Remove grease and oil in drawer with a standard,

nonammable cleaning uid.

3. The use of drawer liners is recommended to

protect the nish inside the drawers and make

the drawers easier to clean. Drawer liners can be

cleaned with soap and water.

4. Lubricate the slides semi-annually with general

purpose grease or equivalent.

Grease

Points

Cleaning

This steel product has been coated with industrial

powder coating for a durable nish. To help protect

the powder coated nish, do not allow harsh chemi-

cals (oil, grease or other chemical) to remain on the

powder coating surface. Use a glass cleaner to

clean and maintain all surfaces of powder coating.

Keep the chest/cabinet handles and wheels clean,

dry and free of oil or grease. Use only mild soap

and a damp cloth to clean your chest/cabinet since

certain cleaning agents and solvents are harm-

ful to plastics. Some of these include: gasoline,

turpentine, lacquer thinner, chlorinated cleaning

solvents, ammonia and household detergents

containing ammonia. Never use flammable or

combustible solvents around chests/cabinets.

Service

For service and repair information, including the or-

dering of service parts, call our Corporate After Sales

Service Technical Support line at 1-800-SAWDUST,

or visit our website at www.milwaukeetool.com.

ACCESSORIES

WARNING

Modifying the chest/cabinet to ac-

cept other accessories may be

hazardous, resulting in injury or property dam-

age. Use only specically recommended acces-

sories according to the manufacturer's instruc-

tions.

For a complete listing of accessories, go online to