Instructions / Assembly

ManualsBrandsMilwaukee ManualsPortable Tool BoxesCustomizable Medium Compact Case for Impact Driver Accessories

54-49-8400

SERVICE PARTS LIST

BULLETIN NO.

MILWAUKEE TOOL

www.milwaukeetool.com

13135 W. LISBON RD., BROOKFIELD, WI 53005

Drwg. 1

EXAMPLE:

Component Parts (Small #) Are Included

When Ordering The Assembly (Large #).

48-22-8426

PACKOUT™ Rolling Tool Box Assembly

July 2017

REVISED BULLETIN

WIRING INSTRUCTION

DATE

CATALOG NO.

SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS

SERIAL

NUMBER

FIG. PART NO. DESCRIPTION OF PART NO. REQ.

1 43-62-8400T Retractable Handle Grip Service Kit (1)

2 --------------- Screw (2)

3 43-62-8400 Retractable Handle Service Assembly (1)

4 --------------- Screw (2)

5 43-62-8426 Side Handle Service Kit

(Contains 2 Side Handles and 4 Pins) (1)

6 --------------- Pin (4)

7 45-94-8426 Wheel Service Kit

(Contains 2 Wheels and 2 Locking Hex Nuts) (1)

8 --------------- Locking Hex Nut (2)

9 44-22-8400 Latch Service Assembly (Set of 2) (1)

10 31-01-8400 Storage Tray (1)

11 43-44-8400 Lid Gasket (Not Shown) (1)

As an aid to removing a damaged Latch

Assembly (9), use two large at blade

screwdrivers. Push blades between parts

as shown. Twist both screwdrivers at same

time to force the blades into opening and

work the latch assembly over the two

locking tabs.

To install a new latch assembly,

position entire latch assembly over

locking tabs with the two top lugs

partially inserted in 'catch cavity' of

main housing. Engage latch bar

onto lid and gently press latch lever

to slide assembly over two locking

tabs and into place.

This removal and installation process will be the same

where other service latches are offered in this system.

2(2x)

4(2x)

Place flat blade

screwdriver in

here and work

pin to the inside.

Grab exposed pin with needle

nose pliers and work out.

Locking Tabs

Latch Assembly

NOTE:

See page 2 for

installation

instructions

of Retactable

Handle (3) into

tool box body.

48-22-8425 PACKOUT™ Large Tool Box Assembly Page 3

48-22-8424 PACKOUT™ Medium Tool Box Assembly Page 3

48-22-8430 PACKOUT™ Organizer Assembly Page 4

48-22-8435 PACKOUT™ Compact Organizer Assembly Page 4

48-22-8310 PACKOUT™ Small 10" Storage Tote Page 4

48-22-8315 PACKOUT™ Medium 15" Storage Tote Page 4

48-22-8320 PACKOUT™ Large 20" Storage Tote Page 4

Summary of content (4 pages)

PAGE 1
BULLETIN NO. SERVICE PARTS LIST SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS PACKOUT™ Rolling Tool Box Assembly SERIAL 48-22-8426 NUMBER CATALOG NO. 00 54-49-8400 REVISED BULLETIN DATE July 2017 WIRING INSTRUCTION EXAMPLE: 0 Component Parts (Small #) Are Included When Ordering The Assembly (Large #).
PAGE 2
Extend Retractable Handle Assembly (3) beyond bottom opening in tool box to see the holes that must line up prior to securing with screws (4). Push assembly back into channel so bottom of handle section shown is flush with bottom of channel. This should be very close to aligning the holes. To be sure, a thin pick can be used in hole to make adjustments.
PAGE 3
48-22-8425 PACKOUT™ Large Tool Box FIG. 1 2 3 4 5 6 7 PART NO. 43-62-8425 --------------43-62-8435 --------------44-22-8400 31-01-8400 43-44-8400 DESCRIPTION OF PART Top Handle Service Kit Pin Side Handle Service Kit Pin Latch Service Assembly (Set of 2) Storage Tray Lid Gasket (Not Shown) NO. REQ. (1) (2) (1) (2) (1) (1) (1) 1 6 2 2 (2x) 5 (2x) 3 4 4 (2x) 48-22-8424 PACKOUT™ Medium Tool Box FIG. 3 4 5 7 8 8a 8b 8c PART NO.
PAGE 4
8-22-8430 PACKOUT™ Organizer FIG. 3 4 5 7 9 9a 9b PART NO. 43-62-8430 --------------44-22-8430 43-44-8430 31-01-0501 ----------------------------- DESCRIPTION OF PART Side Handle Service Kit Pin Latch Service Assembly (Set of 2) Lid Gasket (Not Shown) 5 Bin Kit (Set of 1) Large Bin Small Bin NO. REQ. (1) (2) (1) (1) (2) (1) (4) ð 9 9a 9b 9a 9b (4x) 9 9a 9b 5 (2x) 9a 9b (2x) 4 (2x) 3 3 4 (2x) 4 ñ 4 48-22-8435 PACKOUT™ Compact Organizer FIG. 3 4 7 9 9a 9b PART NO.