Replacement Part List

M18™ FUEL™ STRING TRIMMER
2725-20
H35A
54-49-2710
See Page 3
Apr. 2017
REVISED BULLETIN
SERVICE PARTS LIST
BULLETIN NO.
WIRING INSTRUCTION
DATE
SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS
CATALOG NO.
STARTING
SERIAL NO.
FIG. PART NO. DESCRIPTION OF PART NO. REQ.
1 --------------- Lower Cover Halve-Left 1
2 --------------- Housing Support-Left Housing Halve 1
3 --------------- Motor Insulator-Left 1
10 --------------- Motor Insulator-Right 1
11 06-82-1080 M3 x 14mm Pan Hd. ST T-10 Screw 6
12 --------------- Housing Cover-Right Housing Halve 1
13 05-88-1200 M4 x 16mm Pan Hd. ST T-20 Screw 9
14 --------------- Lower Cover Halve-Right 1
15 05-88-1300 M4 x 28mm Pan Hd. ST T-20 Screw 2
16 05-88-5375 M4 x 13.5 Pan Hd. ST T-20 Screw 1
19 42-68-0292 Carrier Handle Clip 2
20 05-55-0006 M6 Hex Nut 2
21 02-04-0034 Ball Bearing 1
22 --------------- Rotor with Drive Shaft Coupling 1
24 06-82-7240 6-19 x 1/2" Pan Hd. ST T-15 Screw 4
25 45-72-0083 On-Off Trigger 1
26 45-72-0084 Release Trigger 1
28 05-74-0013 M4 x 20mm Hex Skt. Hd. Cap Screw (Silver) 1
29 44-34-0095 Motor Mount Assembly with Bearing 1
30 05-55-0004 M4 Hex Nut (Silver) 1
31 40-50-0373 Spring 1
32 05-74-0015 M6 x 21.5mm, 5mm Hex Socket Cap Screw 4
33 --------------- Carrier Handle 1
41 05-81-0131 M6 x 18mm, 5mm Hex Flat Hd. Screw 1
42 05-85-0080 M8 x 1.25 Hex Hd. Screw 1
43 --------------- String Guard 1
44 42-26-0024 Line Cut-Off Blade 1
45 05-74-0935 M5 x 15mm Pan Hd. T-25 Machine Screw 2
46 05-81-0132 M6 x 14mm Pan Hd. T-30 Machine Screw 4
52 44-66-0029 Lock Plate Assembly 1
59 14-30-0205 Gearcase Assembly 1
60 14-32-0140 String Guard Assembly 1
61 14-34-0124 Carrier Handle Assembly 1
62 14-20-0056 Electronics Assembly 1
62a --------------- On-Off Switch 1
62b --------------- Two Speed Selector/PCBA Assembly 1
62c --------------- Battery Connector/PCBA Assembly 1
62d --------------- Hall Board Assembly 1
62e --------------- Stator Assembly 1
63 31-44-0181 Lower Cover Kit 1
MILWAUKEE TOOL
l
www.milwaukeetool.com
13135 W. Lisbon Road, Brookeld, WI 53005
Drwg. 2
42
41
46
(4x)
52
44
45
(2x)
19
(2x)
33
20
(2x)
32
(2x)
12
13
(9x)
15
(2x)
14
70
16
(1x)
11
(6x)
10
24
(4x)
21
22
28
29
30
25
26
31
2
3 1
32
(2x)
68
69
62a
62b
62c
62d
62e
43
1 14
70
63
2 12
86
64
43 44
45 46
60
3
10
65
19 20
32 33
61
21
22
67
42
59
28 29
30 67
71
68
66
62a 62b 62c
62d 62e
62
2
Rubber Pads with adhesive (86) are to
be placed in both Housing Halves
(2 and 12).
13 9x
15 2x
16 1x
42
Hex Hd.
Screw
59
Gearcase
Assembly
It is recommended to lubricate Gearcase
Assembly (59) at 50 hour intervals. Remove
Hex Head Screw (42) and place 9.5-11.5g of
Type 'Y' grease, 49-08-5270 inside Gearcase.
DO NOT OVERFILL.
Remove #42 and apply
grease through a
squeeze tube or
use a manual
grease gun.
86(2x)
NOTE:
There are two designs
for the Replacement
String Trimmer Head.
See Page Two.
FIG. PART NO. DESCRIPTION OF PART NO. REQ.
64 31-44-0182 Housing Kit 1
65 31-50-0881 Motor Insulator Kit 1
66 45-08-0174 Drive Shaft Assembly 1
67 16-01-0021 Rotor Assembly 1
68 10-20-1043 Warning Label 1
69 40-50-0374 Bias Spring 1
70 12-20-0088 Service Nameplate 1
71 14-50-2725 Rotor/Motor Mount Assembly 1
84 49-96-0012 5mm Hex Key (Not Shown) 1
85 49-96-0055 T-30 Key (Not Shown) 1
86 44-52-0001 Rubber Pad with Adhesive (Set of 2) 1