Use and Care Manual

7
Attaching the Shoulder Strap
(Available as an accessory)
When using this attachment with larger-capacity
battery packs, use the shoulder strap to reduce
user fatigue and help in maintaining control of the
tool during use.
To install the strap:
Nut
Bolt
Pole
clip
Bevel
Gate
Carabiner
1. Remove the battery
pack.
2. Fit the pole clip around
the power head pole
between the front han-
dle and rear handle in
a location comfortable
during use.
3. Insert the bolt through
the pole clip and strap
bevel. Thread the nut
onto the bolt and tight-
en securely.
4. Clip the strap cara-
biner to the bevel.
To wear the strap:
1. Put your right arm
and head through the
strap.
2. Adjust the strap clips
to change the strap
length to t comfort-
ably.
3. Slide the neck pad to
the appropriate posi-
tion.
To unclip the strap:
1. Hold the tool by the front handle with your left hand.
2. Grip the carabiner with your right hand and unclip
by pushing in the gate and it sliding o󰀨 the bevel.
Quik-Lok™ System
Extension Attachment
(Available as an accessory)
Do not extend tool by more than one extension
attachment. Additional extension attachments will
make the pole unstable and di󰀩cult to control, which
could result in injury.
To install an attachment or extension:
1. Remove battery pack.
2. Loosen the lock knob.
3. Slide the pole into the Quik-Lok™ latch. The de-
tent on the pole should line up with the slot in the
Quik-Lok™ latch.
4. Push the sections together securely. Tug on the
poles to ensure they are secure.
5. Tighten the lock knob.


Quik-Lok ™ release button
Detent
Attachment pole
Lock knob
Power head
To remove an attachment or extension:
1. Remove battery pack.
2. Loosen the lock knob.
3. Push in the Quik-Lok™ release button and pull
the poles apart.
Chain Oil
WARNING
Always remove battery pack before
changing or removing accessories.
NOTICE
Fill oil reservoir with chain oil (not
provided) before starting the tool and
when tank is less than 1/4 full. Failure to oil the
chain will cause damage to the bar and chain.
Check oil level frequently and ll the oil reservoir after
each full battery discharge. Use a high quality chain
oil. The oil will keep the saw chain and guide bar
properly lubricated. Never run the tool without chain
oil. Keep the reservoir more than 1/4 full to ensure
su󰀩cient oil is available for the job. Always lightly oil
the chain when storing to prevent rust. Always empty
the oil tank when storing to prevent leakage.
NOTE: It is recommended to use a vegetable based
chain oil when pruning trees. Mineral oil may harm
trees. Never use waste oil automotive oil, or very
thick oils. These could damage the tool.
Filling the Oil Reservoir
1. Remove the battery pack.
2. Place the tool on a at, rm surface, blade side down.
3. Unscrew the oil cap.
4. Carefully ll reservoir with chain oil.
5. Tighten oil cap securely.
6. Repeat as needed during use.
7. Periodically check that the saw chain is lubricat-
ing correctly:
• With a full reservoir, hold the tool with the tip of
the guide bar pointing down toward a light-colored
surface.
• Run the tool for approximately 30 seconds.
• An oil line should become visible on the light
surface.
• If not, remove and clean the guide bar thoroughly.
Ensure the guide bar sprocket (at the tip) rotates
freely.
• If the lubrication system still does not work prop-
erly, contact a MILWAUKEE service facility.
Transporting Tool
WARNING
Carry the tool by the front handle
to avoid accidental starting. Prop-
er handling of the tool will prevent injury.
Always turn o󰀨 the tool when transporting from
one location to another. Do not carry tool with
nger on the trigger. Accidental starting can
cause serious personal injury.
Before transporting, always:
1. Remove the battery pack
2. Place the cover over the guide bar.
Selecting the Speed
When using this attachment, only HIGH
High
Low
SPEED is recommended. Use the speed
control button to select HIGH SPEED.