TM MANUAL DE INSTRUCCIONES MANUAL DO OPERADOR OPERATOR'S MANUAL Cat. No. 6278-59 6278-59A 6278-59B SIERRA CALADORA SERRA TICO-TICO JIG SAW ADVERTENCIA PARA REDUCIR EL RIESGO DE LESIONES, EL USUARIO DEBE LEER Y ENTENDER EL MANUAL DEL OPERADOR. AVISO PARA REDUZIR O RISCO DE ACIDENTES, O USUÁRIO DEVE LER E ENTENDER O MANUAL DO OPERADOR. WARNING TO REDUCE THE RISK OF INJURY, USER MUST READ AND UNDERSTAND OPERATOR'S MANUAL.
ADVERTENCIAS DE SEGURIDAD GENERALES PARA LA HERRAMIENTA ELÉCTRICA ADVERTENCIA LEA TODAS LAS ADVERTENCIAS E INSTRUCCIONES DE SEGURIDAD. Si no sigue todas las advertencias e instrucciones, se pueden provocar una descarga eléctrica, un incendio o lesiones graves. Guarde todas las advertencias e instrucciones para consultarlas en el futuro.
TIERRA EXTENSIONES ELECTRICAS Las herramientas que deben conectarse a tierra cuentan con clavijas de tres patas y requieren que las extensiones que se utilicen con ellas sean también de tres cables. Las herramientas con doble aislamiento y clavijas de dos patas pueden utilizarse indistintamente con extensiones de dos a tres cables. El calibre de la extensión depende de la distancia que exista entre la toma de la corriente y el sitio donde se utilice la herramienta.
OPERACION de la herida, no empieza el instrumento con la hoja que contacta el workpiece. ADVERTENCIA Para reducir el riesgo de una lesión, desconecte siempre la herramienta antes de fijar o retirar accesorios, o antes de efectuar ajustes. Utilice sólo los accesorios específicamente recomendados. El uso de otros accesorios puede ser peligroso. Cómo realizar el corte 1. Ajuste la acción orbital de acuerdo al material que va a cortar. 2.
INDICAÇÕES GERAIS DE ADVERTÊNCIA PARA FERRAMENTAS ELÉTRICAS ATENÇÃO DEVEM SER LIDAS TODAS AS INDICAÇÕES DE ADVERTÊNCIA E TODAS AS INSTRUÇÕES. O desrespeito das advertências e instruções apresentadas abaixo pode causar choque elétrico, incêndio e/ou graves lesões.Guarde bem todas as advertências e instruções para futura referência.
As ferramentas aterradas precisam de um cabo extensor com três fios. As ferramentas com isolamento duplo podem utilizar cabos extensores com dois ou três fios. Conforme aumentar a distância da tomada, você precisará usar um cabo extensor de calibre mais grosso. O uso de cabos extensores com fios de tamanho inadequado causa uma grave queda da tensão que resulta em perda de potência e possíveis danos à ferramenta. Consulte a tabela ao abaixo para determinar o tamanho mínimo do fio.
OPERAÇÃO AVISO Para reduzir o risco de ferimentos, sempre retire a ferramenta da tomada antes de fixar ou remover acessórios ou fazer ajustes. Use somente acessórios especificamente recomendados. Outros acessórios podem ser perigosos. AVISO Para reduzir o risco de ferimentos, não ligue a ferramenta com a lâmina em contato com o objeto de trabalho. Fazendo o corte 1. Defina a ação orbital de acordo com o material que será cortado. 2.
GENERAL POWER TOOL SAFETY WARNINGS WARNING READ ALL SAFETY WARNINGS AND ALL INSTRUCTIONS. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference The term "power tool" in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. •Remove any adjusting key or wrench before WORK AREA SAFETY turning the power tool on.
SYMBOLOGY GROUNDING WARNING Improperly connecting the ASSEMBLY grounding wire can result in the risk of electric shock. Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded. Do not modify the plug provided with the tool. Never remove the grounding prong from the plug. Do not use the tool if the cord or plug is damaged. If damaged, have it repaired by a MILWAUKEE service facility before use.
OPERATION WARNING To reduce the risk of injury, always unplug tool before attaching or removing accessories or making adjustments. Use only specifically recommended accessories. Others may be hazardous. WARNING To reduce the risk of injury, do not start the tool with the blade contacting the workpiece. Making the Cut 1. Set the orbital action according the material to be cut. 2. Position the tool with the front part of the shoe on the workpiece and start the tool. 3.
Importado por: Techtronic Ind Argentina SRL Cuit: 33-71069847-9 Av. Leandro N. Alem 110 piso 13 C.A.B.A (1001), BUENOS AIRES ARGENTINA 58-14-9920d5 Importado por: Techtronic Industries Comércio de Ferramentas do Brasil Ltda. Prolongamento da Travessa Claudio Armando, nº 171, Bloco 2, galpão 21. Bairro Assunção, São Bernardo do Campo, SP. CEP: 09861-730 – Brasil CNPJ: 11.857.