Owner's manual

ManualsBrandsMilwaukee ManualsCordless50 m Laser distance meter

1ENGLISH

MPORTANT SAFETY INSTRUCTIONS

Do not use the product before you have studied

the Safety instructions and the User Manual.

Laser Classiﬁ cation

WARNING:

It is a Class 2 laser product in accordance

with EN 60825-1:2007.

Labeling

We have supplied you with an adhesive label in your language

and now request that you please apply this in place of the

English text on the speciﬁ cation plate before ﬁ rst

commissioning the machine.

447701 01

XXXXXX MJJJJ

WARNING:

Avoid direct eye exposure. The laser beam can cause ﬂ ash

blindness.

Do not stare into the laser beam or direct it towards other

people unnecessarily.

Don't dazzle other individuals.

WARNING:

Do not operate the tool around children or allow children to

operate the tool.

The reﬂ ective surface could reﬂ ect the beam back at the

operator or other persons.

Keep extremities in a safe distance from the moving parts.

Carry out periodic test measurements. Particularly before,

during and after important measurements.

Watch out for erroneous measurements if the product is

defective or if it has been dropped or has been misused or

modiﬁ ed.

WARNING: Use of controls, adjustments, or the performance

of procedures other than those speciﬁ ed in the manual may

result in hazardous radiation exposure.

The laser distance measurer has limits of use. (Refer to the

“Technical data” section). Attempts to measure outside the

maximum and minimum range will cause inaccuracy. Use in

adverse conditions including too hot, too cold, very bright

sunlight, rain, snow, fog, or other vision restricting conditions

will result in inaccurate readings.

When the laser distance measurer is brought into a warm

environment from very cold conditions, or vice versa, allow it to

come to the surrounding temperature before use.

Always store the laser distance measurer indoors, avoid

exposing the tool to shock, continuous vibration or extreme

temperatures.

Always keep the tool away from dust, liquids and high humidity.

These may damage internal components or affect accuracy.

Do not use aggressive cleaning agents or solutions. Use only a

clean, soft cloth for cleaning.

Avoid heavy impact to or dropping of the measuring tool. The

accuracy of the tool should be checked before use if it has

been dropped or subjected to other mechanical stresses.

Any repair required on this laser product should be performed

only by authorised service personnel.

Do not operate the product in explosion hazardous areas or in

aggressive environments.

Only use chargers recommended by the manufacturer to

charge the batteries.

Flat batteries must not be disposed of with household

waste. Care for the environment and take them to the

collection points provided in accordance with national or

local regulations. The product must not be disposed with

household waste. Dispose of the product appropriately in

accordance with the national regulations in force in your

country. Adhere to the national and country speciﬁ c regulations.

Please contact your local authority or your dealer for how to

dispose of batteries properly.

European Conformity Mark

CONTENTS

mportant safety instructions ...................................................1

Speciﬁ ed Conditions of Use ...................................................2

Error Code Table ....................................................................2

Overview.................................................................................3

Change batteries ....................................................................4

Corner Pin ..............................................................................4

Belt Clip ..................................................................................4

Function Switch, Measuring Reference, Pythagoras..............5

Single Distance Measuring .....................................................6

Permanent / Minimum-Maximum Measuring ..........................7

Add / Subtract Measuring .......................................................8

Area Measuring ......................................................................9

Volume Measuring ................................................................10

Indirect Measuring (Pythagoras 1) .......................................11

Indirect Measuring (Pythagoras 2) .......................................12

Indirect Measuring (Pythagoras 3) .......................................13

Wall Area Measuring (Scenario 1) ......................................14

Wall Area Measuring (Scenario 2) ......................................15

Timer ....................................................................................16

Memory .................................................................................16

Basic Description on example of Area measuring (1)...........17

Basic Description on example of Area measuring (2)...........18

Summary of content (18 pages)

PAGE 1
CONTENTS Important safety instructions...................................................1 Speciﬁed Conditions of Use ...................................................2 Error Code Table ....................................................................2 Overview.................................................................................3 Change batteries ....................................................................4 Corner Pin .................................................................
PAGE 2
TECHNICAL DATA ERROR CODE TABLE Dust and Water resistance IP54 Code Description Solution Receiving Lens 14 mm Err01 Out of measuring range Measure in a proper range Focus 35 mm Err02 Reﬂect signal is too weak Choose a better surface Maximum Measuring Range 50 meters (Tolerance : 55m) Err03 Minimum Measuring Range 0.05 meters Out of display range (max value: 99.999) e.g.
PAGE 3
OVERVIEW Single Pythagoras Height difference Area/ Volume Indirect Surface Measurement Measuring Reference Battery Status Normal Measuring Mode Memory Timer Minimum / Maximum for continuous Measure Continuous measure mode Among Values Addition / Subtraction Main Value ON / MEASURE ► On ► Measure ► Continuous Measurement (push 2 sec) + Min / Max Function PYTHAGORAS ADD / SUBSTRACT ► Add value ► Subtract value AREAS / VOLUMES ► Area (push 1x) ► Volume (push 2x) ► Indirect Surface Measurement (push
PAGE 4
CHANGE BATTERIES CORNER PIN Change batteries when battery symbol is ﬂashing.
PAGE 5
FUNCTION SWITCH, MEASURING REFERENCE, PYTHAGORAS Area Volume Wall Distance Starting Point of Measure Pythagoras 1 90° Pythagoras 2 90° Pythagoras 3 90° Corner Pin ENGLISH Front Back (Standard automatical) 5
PAGE 6
SINGLE DISTANCE MEASURING 0 1 2 3 4 5 1 3 5 ENGLISH 6
PAGE 7
PERMANENT / MINIMUM-MAXIMUM MEASURING 0 1 2 3 4 Stop MIN / MAX 2 sec 2 sec 2 MAX MIN 90° MAX ENGLISH 7
PAGE 8
ADD / SUBTRACT MEASURING 0 1 2 3 1x 2x 1 3 1,000 m ENGLISH 8
PAGE 9
AREA MEASURING 0 1 2 1x 2 ENGLISH 1 9
PAGE 10
VOLUME MEASURING 0 1 2 3 2x 2 3 ENGLISH 1 10
PAGE 11
INDIRECT MEASURING (PYTHAGORAS 1) 0 1 2 1x 1 90° 2 ENGLISH 11
PAGE 12
INDIRECT MEASURING (PYTHAGORAS 2) 0 1 2 3 2x 1 90° 3 2 ENGLISH 12
PAGE 13
INDIRECT MEASURING (PYTHAGORAS 3) 1 2 3 4 3x 1 2 90° 3 ENGLISH 13
PAGE 14
WALL AREA MEASURING (SCENARIO 1) 0 1 2 3 4 3x 5 4 1 3 2 5 ENGLISH 14
PAGE 15
WALL AREA MEASURING (SCENARIO 2) 0 1 2 3 4 4x 5 1 3 4 2 5 ENGLISH 15
PAGE 16
TIMER With the timer, the measurement can be start delayed. For example to position a part in the measuring beam. Push button - Icon is displayed. Timer can be set between 3 to 15 sec by pressing the button . Push button - The seconds are counted down until the measurement starts. - At 0, the measurement starts. MEMORY The measured values are stored continuously and automatically in memory. The stored values can be retrived by pushing the button . Push the button 2 sec. - Icon and memory number appears.
PAGE 17
BASIC DESCRIPTION ON EXAMPLE OF AREA MEASURING (1) 1 Turn On 2 Choose Measuring Reference 3 Choose Function 4 Measure length 5 Measure width Push Button Attention! Laser on! Do not point it at a person! Standard after turning on: Bottom Push 1x -> Corner Pin Push 2x -> Top Push 3x -> Bottom After switching on the device is always on single distance measurement Push 1x - Area Measurement.
PAGE 18
BASIC DESCRIPTION ON EXAMPLE OF AREA MEASURING (2) 6 View stored values 7 Exit memory 8 Switch off Push button Push button Push button Push button 2 sec (Memory must be exited before) 2 sec. repaeted - Stored values appears in the main line. - Associated icon appears and measured parameter ﬂashes (ﬂashing green illustrated) ENGLISH . - Device switches off. - If no button is pressed, the device switches off automatically after 3 minutes.