Owner's manual

Deutsch
2626
English
GB
WORKING INSTRUCTIONS
Adapt the feed speed to avoid overheating the blade tips.
SPECIFIED CONDITIONS OF USE
This electronic circular saw can cut lengthways and mitre accurately
in wood.
ELECTRIC BRAKE
The electric brake engages when the trigger is released, causing
the blade to stop and allowing you to proceed with your work.
Generally, the saw blade stops within two seconds. However, there
may be a delay between the time you release the trigger and when
the brake engages. Occasionally the brake may miss completely.
If the brake misses frequently, the saw needs servicing by an autho-
rized Milwaukee service facility. You must always wait for the blade
to stop completely before removing the saw from the workpiece.
BATTERIES
Battery packs which have not been used for some time should be
recharged before use.
Temperatures in excess of 50°C (122°F) reduce the performance of
the battery pack. Avoid extended exposure to heat or sunshine (risk
of overheating).
The contacts of chargers and battery packs must be kept clean.
For an optimum life-time, the battery packs have to be fully char-
ged, after use. Battery packs which have not been used for some
time should be recharged before use.
To obtain the longest possible battery life remove the battery pack
from the charger once it is fully charged.
For battery pack storage longer than 30 days: Store the battery
pack where the temperature is below 27°C and away from moisture
Store the battery packs in a 30% - 50% charged condition Every six
months of storage, charge the pack as normal.
Do not dispose of used battery packs in the household refuse or
by burning them. Milwaukee Distributors oer to retrieve old
batteries to protect our environment.
Do not store the battery pack together with metal objects (short
circuit risk).
Battery acid may leak from damaged batteries under extreme load
or extreme temperatures. In case of contact with battery acid wash
it o immediately with soap and water. In case of eye contact rinse
thoroughly for at least 10 minutes and immediately seek medical
attention.
No metal parts must be allowed to enter the battery section of the
charger (short circuit risk).
BATTERY PACK PROTECTION
In extremely high torque, binding, stalling and short circuit
situations that cause high current draw, the tool will stop for about
2 seconds and then the tool will turn OFF. To reset, release the
trigger.
Under extreme circumstances, the internal temperature of the
battery pack could raise too much. If this happens, the fuel gauge
will ash until the battery pack cooled down. After the lights go o,
the work may continue.
Place the battery on the charger to charge and reset it.
TRANSPORTING LITHIUM BATTERIES
Lithium-ion batteries are subject to the Dangerous Goods Legisla-
tion requirements.
Transportation of those batteries has to be done in accordance with
local, national and international provisions and regulations.
The user can transport the batteries by road without further
requirements.
Commercial transport of Lithium-Ion batteries by third parties is
subject to Dangerous Goods regulations. Transport preparation and
transport are exclusively to be carried out by appropriately trained
persons and the process has to be accompanied by corresponding
experts.
When transporting batteries:
Ensure that battery contact terminals are protected and insulated
to prevent short circuit. Ensure that battery pack is secured against
movement within packaging. Do not transport batteries that are
cracked or leak. Check with forwarding company for further advice
MAINTENANCE
Remove the battery pack before starting any work on the
appliance.
Be sure to disconnect the tool from the power supply before
attaching or removing the saw blade.
Clean tool and guarding system with dry cloth.
Certain cleaning agents and solvents are harmful to plastics and
other insulated parts.
Keep the apparatus handle clean, dry and free of spilt oil or grease.
Check the function of guards.
Regular maintenance and cleaning provide for a long service life
and safe handling.
The ventilation slots of the machine must be kept clear at all times.
Remove dust regularly. Remove the sawdust which has accummu-
lated inside the saw in order to avoid the risk of re.
Use only Milwaukee accessories and Milwaukee spare parts. Should
components need to be replaced which have not been described,
please contact one of our Milwaukee service agents (see our list of
guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please state
the Article No. as well as the machine type printed on the label
and order the drawing at your local service agents or directly at:
Techtronic Industries GmbH, Max-Eyth-Straße10,
71364Winnenden, Germany.