M18 FCS66 Original instructions
M18 FCS66 Original instructions Originalbetriebsanleitung Notice originale Istruzioni originali Manual original Manual original Oorspronkelijke gebruiksaanwijzing Original brugsanvisning Original bruksanvisning Bruksanvisning i original Alkuperäiset ohjeet Algupärane kasutusjuhend Πρωτότυπο οδηγιών χρήσης Оригинальное руководство по эксплуатации Orijinal işletme talimatı Původním návodem k používání Оригинално ръководство за експлоатация Pôvodný návod na použitie Instrucţiuni de folosire originale Instrukc
I II III IV V VI VII VIII IX X XI XII 90° Technical Data,Safety Instructions, Specified Conditions of Use, Declaration of Conformity, Batteries, Maintenance, Symbols Please read and save these instructions!
1. I 2 1 2.
1. 2. 1. 2.
TIP 78-100 % II 55-77 % 33-54 % 10-32 % <10 % 5
1. III 1 2 2.
3. III EN 847-1 4.
5. III 1 2 6.
STOP START 1 IV 2 For safety reasons this power tool is fitted with a switch lock and the On-/Off switch cannot be locked in the „On“ position 9
IV Insulated gripping surface 10
V Adjust the cutting depth to the thickness of the workpiece. Less than a full tooth of the blade teeth should be visible below the workpiece.
1. 2. V 3.
1. 2. VI 50 45 40 30 20 10 0 3. 4.
1. 2. VII 2 1 3.
1. 2. START VIII 1 2 3. 2. 0° 4.
1. VIII 0° > 0° 2. 3. START 1 2 4. 16 5. 2. 6.
A IX B max.
IX 18
90° 2. 90° 1. X 0° If a correction of the 90° angle of the guide-plate to the saw blade is necessary, use the correction screw.
90° 90° 3. X + + – 90° 4.
1. A AS 2-250 4931 4472 95 B AS300 AS-30 AS-42 4931 4472 94 1 XI 2 2.
TECHNICAL DATA Circular saw Production code XII Battery voltage No-load speed Saw blade dia. x hole dia Saw blade thickness Blade teeth Max. Cutting depth at 0° / 45° / 56° Weight according EPTA-Procedure 01/2014 (Li-Ion 2,0 Ah ... 12,0 Ah) Recommended Ambient Operating Temperature Recommended battery types Recommended charger Noise information Measured values determined according to EN 62841.
Kickback causes and related warnings – kickback is a sudden reaction to a pinched, jammed or misaligned saw blade, causing an uncontrolled saw to lift up and out of the workpiece toward the operator; – when the blade is pinched or jammed tightly by the kerf closing down, the blade stalls and the motor reaction drives the unit rapidly back toward the operator; – if the blade becomes twisted or misaligned in the cut, the teeth at the back edge of the blade can dig into the top surface of the wood causing the
brake engages. Occasionally the brake may miss completely. If the brake misses frequently, the saw needs servicing by an authorized Milwaukee service facility. You must always wait for the blade to stop completely before removing the saw from the workpiece. XII BATTERIES Battery packs which have not been used for some time should be recharged before use. Temperatures in excess of 50°C (122°F) reduce the performance of the battery pack. Avoid extended exposure to heat or sunshine (risk of overheating).
GB-DECLARATION OF CONFORMITY We declare as the manufacturer under our sole responsibility that the product described under „Technical Data“ fulfills all the relevant provisions of the following Regulations S.I. 2012/3032 (as amended), S.I. 2008/1597 (as amended), S.I.
Copyright 2020 Techtronic Industries GmbH Max-Eyth-Straße 10 71364 Winnenden Germany +49 (0) 7195-12-0 www.milwaukeetool.eu Techtronic Industries (UK) Ltd Fieldhouse Lane Marlow Bucks SL7 1HZ UK (11.
