Owner's manual

18 19
M18 FJS
...................................4692 59 02...
...000001-999999
........................................ 18 V
................................. 0-3500
min
-1
(+/- 10%)
........................................ 25 mm
.......................................45°
...................................... 100 mm
........................................ 19 mm
........................................ 10 mm
........................... 2,63 - 3,69 kg
.............................. -18...+50 °C
.......................M18B2... M18B9, M18HB12
............................M12-18 ... ; M1418C6
................................... 88,68 dB (A)
................................... 99,68 dB (A)
................................... 21,25 m/s
2
....................................... 1,5 m/s
2
................................... 17,34 m/s
2
....................................... 1,5 m/s
2
TECHNICAL DATA CORDLESS JIGSAW
Production code....................................................................................................................
Battery voltage......................................................................................................................
Stroke rate under no-load .....................................................................................................
Length of stroke ....................................................................................................................
Bevel cuts up to ....................................................................................................................
Cutting depth max. in:
Wood ................................................................................................................................
Aluminium ........................................................................................................................
Steel .................................................................................................................................
Weight according EPTA-Procedure 01/2014 (2.0 - 12.0 Ah) ................................................
Recommended ambient operating temperature ...................................................................
Recommended battery types................................................................................................
Recommended charger ........................................................................................................
Noise/vibration information
Measured values determined according to EN 62841.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level (Uncertainty K=3dB(A)) .....................................................................
Sound power level (Uncertainty K=3dB(A)) ..........................................................................
Wear ear protectors!
Total vibration values (vector sum in the three axes) determined according to EN 62841.
Sawing of wood *1
Vibration emission value a
h
..............................................................................................
Uncertainty K ....................................................................................................................
Sawing of sheet metal *2
Vibration emission value a
h
..............................................................................................
Uncertainty K ....................................................................................................................
*1 with saw blade BIM, dimension 100 x 7,5 x 1,0 mm and tooth pitch 2,5 mm
*2 with saw blade BIM, dimension 75 x 7,5 x 1,0 mm and tooth pitch 1,8 mm
WARNING Read all safety warnings, instructions, illustrations and
specifi cations provided with this power tool. Failure to follow all instructions listed below
may result in electric shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.
JIG SAW SAFETY WARNINGS
Hold the power tool by insulated gripping surfaces, when performing an operation
where the cutting accessory may contact hidden wiring.
Cutting accessory contacting a „live“ wire may make exposed metal parts of the power tool
„live“ and could give the operator an electric shock.
Use clamps or another practical way to secure and support the workpiece to a stable
platform. Holding the work by your hand or against the body leaves it unstable and may
lead to loss of control.
Wear ear protectors. Exposure to noise can cause hearing loss.
ADDITIONAL SAFETY AND WORKING INSTRUCTIONS
Use protective equipment. Always wear safety glasses when working with the machine. The
use of protective clothing is recommended, such as dust mask, protective gloves, sturdy
non-slip footwear, helmet and ear defenders.
The dust produced when using this tool may be harmful to health. Do not inhale the dust.
Wear a suitable dust protection mask.
Do not machine any materials that present a danger to health (e.g. asbestos).
Switch the device off immediately if the insertion tool stalls! Do not switch the device on
again while the insertion tool is stalled, as doing so could trigger a sudden recoil with a high
reactive force. Determine why the insertion tool stalled and rectify this, paying heed to the
safety instructions.
The possible causes may be:
• it is tilted in the workpiece to be machined
• it has pierced through the material to be machined
• the power tool is overloaded
Do not reach into the machine while it is running.
The insertion tool may become hot during use.
WARNING! Danger of burns
• when changing tools
• when setting the device down
Chips and splinters must not be removed while the machine is running.
When working in walls ceiling, or fl oor, take care to avoid electric cables and gas or
waterpipes.
Clamp your workpiece with a clamping device. Unclamped workpieces can cause severe
injury and damage.
Do not use cracked or distorted saw blades.
Plunge cuts without pre-drilling a hole are possible with soft materials (wood, light
building materials for walls). Harder materials (metals) must fi rst be drilled with a hole
corresponding to the size of the saw blade.
Remove the battery pack before starting any work on the machine.
Do not dispose of used battery packs in the household refuse or by burning them.
Milwaukee Distributors off er to retrieve old batteries to protect our environment.
Do not store the battery pack together with metal objects (short circuit risk).
No metal parts must be allowed to enter the battery section of the charger (short circuit risk).
Use only System M18 chargers for charging System M18 battery packs. Do not use
battery packs from other systems.
Never break open battery packs and chargers and store only in dry rooms. Keep dry at
all times.
Battery acid may leak from damaged batteries under extreme load or extreme
temperatures. In case of contact with battery acid wash it off immediately with soap and
water. In case of eye contact rinse thoroughly for at least 10 minutes and immediately
seek medical attention.
Warning! To reduce the risk of fi re, personal injury, and product damage due to a short
circuit, never immerse your tool, battery pack or charger in fl uid or allow a fl uid to fl ow
inside them. Corrosive or conductive fl uids, such as seawater, certain industrial
chemicals, and bleach or bleach containing products, etc., can cause a short circuit.
SPECIFIED CONDITIONS OF USE
This jig saw can cut wood, plastic and metal; it can cut straight lines, bevels, curves, and
internal cut-outs.
Do not use this product in any other way as stated for normal use.
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that the product described under “Technical
Data” fulfi lls all the relevant regulations and the directives 2011/65/EU (RoHS), 2014/30/
EU, 2006/42/EC, and the following harmonized standards have been used:
ENGLISH
WARNING
The vibration emission level given in this information sheet has been measured in accordance with a standardized test given in EN 62841 and may be used to compare one tool with
another. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main applications of the tool. However if the tool is used for diff erent applications, with diff erent accessories or poorly maintained, the
vibration emission may diff er. This may signifi cantly increase the exposure level over the total working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or when it is running but not actually doing the job. This may
signifi cantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the eff ects of vibration such as: maintain the tool and the accessories, keep the hands warm, organisation of work
patterns.
ENGLISH
EN 62841-1:2015
EN 62841-2-11:2016+A1:2020
EN 55014-1:2017+A11:2020
EN 55014-2:2015
EN IEC 63000:2018:2012
Winnenden, 2020-10-26
Alexander Krug
Managing Director
Authorized to compile the technical fi le
Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Germany
GB-DECLARATION OF CONFORMITY
We declare as the manufacturer under our sole responsibility that the product described
under “Technical Data” fulfi lls all the relevant provisions of the following Regulations S.I.
2008/1597 (as amended), S.I. 2016/1091 (as amended), S.I. 2012/3032 (as amended) and
that the following designated standards have been used:
BS EN 62841-1:2015
BS EN 62841-2-11:2016+A1:2020
BS EN 55014-1:2017+A11:2020
BS EN 55014-2:2015
BS EN IEC 63000:2018:2012
Winnenden, 2020-10-26
Alexander Krug
Managing Director
Authorized to compile the technical fi le.
Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Germany
LOAD-DEPENDENT MOTOR PROTECTION:
If the motor is overloaded, the overload protection will trip. To continue working, switch
the machine off and then on again."
SOFT START
Electronic smooth start for save use prevents jerky run-up of the machine.
BATTERIES
Battery packs which have not been used for some time should be recharged before use.
Temperatures in excess of 50°C (122°F) reduce the performance of the battery pack.
Avoid extended exposure to heat or sunshine (risk of overheating).
The contacts of chargers and battery packs must be kept clean.
For an optimum life-time, the battery packs have to be fully charged, after use.
To obtain the longest possible battery life remove the battery pack from the charger once
it is fully charged.
For battery pack storage longer than 30 days:
Store the battery pack where the temperature is below 27°C and away from moisture
Store the battery packs in a 30% - 50% charged condition
Every six months of storage, charge the pack as normal.
BATTERY PACK PROTECTION LI-ION BATTERY
The battery pack has overload protection that protects it from being overloaded and
helps to ensure long life.
Under extreme stress the battery electronics switch off the machine automatically. To
restart, switch the machine off and then on again. If the machine does not start up again,
the battery pack may have discharged completely. In this case it must be recharged in
the battery charger.
TRANSPORTING LITHIUM BATTERIES
Lithium-ion batteries are subject to the Dangerous Goods Legislation requirements.
Transportation of those batteries has to be done in accordance with local, national and
international provisions and regulations.
• The user can transport the batteries by road without further requirements.
• Commercial transport of Lithium-Ion batteries by third parties is subject to Dangerous
Goods regulations. Transport preparation and transport are exclusively to be carried
out by appropriately trained persons and the process has to be accompanied by
corresponding experts.
When transporting batteries:
• Ensure that battery contact terminals are protected and insulated to prevent short
circuit.
• Ensure that battery pack is secured against movement within packaging.
• Do not transport batteries that are cracked or leak.
Check with forwarding company for further advice
MAINTENANCE
The ventilation slots of the machine must be kept clear at all times.
Use only Milwaukee accessories and spare parts. Should components need to be
replaced which have not been described, please contact one of our Milwaukee service
agents (see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please state the Article No. as
well as the machine type printed on the label and order the drawing at your local service
agents or directly at: Techtronic Industries GmbH, Max-Eyth-Straße 10,
71364 Winnenden, Germany.
SYMBOLS
CAUTION! WARNING! DANGER!
Remove the battery pack before starting any work on the machine.
Please read the instructions carefully before starting the machine.
Always wear goggles when using the machine.
Wear gloves!
Wear ear protectors!
Accessory - Not included in standard equipment, available as an
accessory.
Do not dispose electric tools, batteries/rechargeable batteries together
with household waste material.
Electric tools and batteries that have reached the end of their life must
be collected separately and returned to an environmentally compatible
recycling facility.
Check with your local authority or retailer for recycling advice and
collection point.
n
0
Stroke rate under no-load
V
Volts
Direct current
European Conformity Mark
British Confomity Mark
Ukraine Conformity Mark
EurAsian Conformity Mark