Owner's manual

2727
GB
GB
Technical Data
Mitresaw
M18 FMS305
Production code 4696 77 02...
...000001 - 999999
No-load speed 3600 min
-1
Battery voltage 18 V
Frequency band 2402 MHz - 2480 MHz
Radio-frequency power 1,8 dBm
Bluetooth version BLE113 BT
Saw blade dia. x hole dia 305 x 30 mm
Saw blade body thickness max.
Saw blade tooth thickness min.
2,2 mm
3,0 mm
Recommended Ambient Operating Temperature - 18 °C ... +50 °C
Recommended battery types M18B..., M18HB...
Recommended charger M12-18..., M1418 C6
Max. cutting capacity
Mitre 0°/ Bevel 0°
Mitre 45°/ Bevel 0°
Mitre 0°/ Bevel L45°
Mitre 0°/ Bevel R45°
Mitre L45°/ Bevel L45°
Mitre L45°/ Bevel R45°
Mitre R45°/ Bevel L45°
Mitre R45°/ Bevel R45°
340 mm x 96,5 mm
235 mm x 96,5 mm
340 mm x 65 mm
340 mm x 40 mm
235 mm x 65 mm
235 mm x 40 mm
235 mm x 65 mm
235 mm x 40 mm
Weight according EPTA-Procedure 01/2014 (Li-Ion 2,0 ... 12,0 Ah) 21,9 ... 23,0 kg
Noise information
Measured values determined according to EN 62841. Typically, the A-weighted noise levels of the tool are
Sound pressure level (Uncertainty K=3dB(A))
Sound power level (Uncertainty K=3dB(A))
Wear ear protectors!
96,2 db(A)
107,5 db(A)
WARNING!
The declared noise emission value(s) were measured according to a standardized test method according to EN 62841 and can be used to compare one
power tool with another. The declared noise emission value(s) may also be used in a preliminary assessment of exposure.
The noise emissions during actual use of the power tool can dier from the declared values depending on the ways in which the tool is used especially
what kind of workpiece is processed.
Identify safety measures to protect the operator that are based on an estimation of exposure in the actual conditions of use (taking account of all parts
of the operating cycle such as the times when the tool is switched o and when it is running idle in addition to the trigger time).
Wear ear protectors. Exposure to noise can cause hearing loss.
WARNING Read all safety warnings, instructions,
illustrations and specications provided with this power tool.
Failure to follow all instructions listed below may result in electric shock,
re and/or serious injury.
Save all warnings and instructions for future reference.
SAFETY INSTRUCTIONS FOR MITRE SAWS
a) Mitre saws are intended to cut wood or wood-like products,
they cannot be used with abrasive cut-o wheels for cutting
ferrous material such as bars, rods, studs, etc. Abrasive dust cau-
ses moving parts such as the lower guard to jam. Sparks from abrasive
cutting will burn the lower guard, the kerf insert and other plastic parts.
b) Use clamps to support the workpiece whenever possible. If
supporting the workpiece by hand, you must always keep your
hand at least 100 mm from either side of the saw blade. Do
not use this saw to cut pieces that are too small to be securely
clamped or held by hand. If your hand is placed too close to the saw
blade, there is an increased risk of injury from blade contact.
c) The workpiece must be stationary and clamped or held
against both the fence and the table. Do not feed the workpi-
ece into the blade or cut “freehand” in any way. Unrestrained or
moving workpieces could be thrown at high speeds, causing injury.
English