Owner's manual

1918
• Ensure that battery pack is secured against movement within
packaging.
• Do not transport batteries that are cracked or leak.
Check with forwarding company for further advice
OPERATION
There are two ways for working with this nailer (see also picture
section):
Single Sequential Actuation:
Drive the fastener by pulling the trigger.
Contact (Bump) Actuation:
Hold the trigger and drive the fastener by pushing the nailer against
the workpiece.
Reload Indicator
To indicate that the magazine is almost empty of fasteners (about 4-5
left), the workpiece contact will not compress, preventing operation
under usual pressure. Install more fasteners to continue working.
Setting the Depth of Drive (see picture section)
Know what is behind your workpiece. A fastener could travel through
the workpiece and out the other side, striking a bystander and causing
serious injury. Lower the depth of drive to prevent the fastener from
being pushed all the way through the workpiece.
REQUIRED DAILY TESTING
WARNING: To reduce the risk of injury to yourself and others,
test the tool before beginning work each day or if the tool is
dropped, received a sharp blow, been run over, etc. Complete the
following checklist IN ORDER. If the tool does not work as it
should, contact a MILWAUKEE service facility immediately.
Always point tool away from yourself and others.
1. Remove battery pack.
WARNING! Always point the tool away from yourself and others
when installing fasteners. Failure to do so could result in injury.
2. Check all screws, bolts, nuts, and pins on the tool. Any loose
fasteners must be tightened.
3. Pull back the fastener pusher on the magazine (to override the
Reload Indicator) and press the workpiece contact against a
workpiece. It must move smoothly.
4. With the workpiece contact pressed against the workpiece, pull the
trigger. It must move smoothly.
5. Insert battery pack.
6. Select the Single Sequential Actuation Operation. Without pulling
the trigger, pull back the fastener pusher on the magazine (to
override the Reload Indicator) and press the workpiece contact
against a workpiece. The tool must not operate. Holding the
workpiece contact away from the workpiece, pull back the fastener
pusher on the magazine (to override the Reload Indicator). Pull
and hold the trigger for 5 seconds. The tool must not operate.
Continue to pull and hold the trigger and push the workpiece
contact against a workpiece. The tool must not operate. Without
pulling the trigger, pull back the fastener pusher on the magazine
(to override the Reload Indicator) and press the workpiece contact
against a workpiece. Pull the trigger. The tool must operate.
Release the trigger. The driver must move up.
7. Select the Contact Actuation Operation. Holding the workpiece
contact away from the workpiece, pull back the fastener pusher on
the magazine (to override the Reload Indicator) and pull the
trigger. The tool must not operate. Continue to pull and hold the
trigger and push the workpiece contact against a workpiece. The
tool must operate.
8. If all previous tests work properly, set the tool for your work. Select
the operation and load fastener strips.
9. Set the depth of drive according to the "Setting the Depth of Drive"
section and see picture section.
10. If all tests operate properly, the tool is ready for use. Repeat these
tests before use each day or if the tool is dropped, received a
sharp blow, been run over, jammed, etc.
MAINTENANCE
The ventilation slots of the machine must be kept clear at all times.
Use only Milwaukee accessories and Milwaukee spare parts. Should
components need to be replaced which have not been described,
please contact one of our Milwaukee service agents (see our list of
guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please state
the machine type printed as well as the six-digit No. on the label and
order the drawing at your local service agents or directly at: Techtronic
Industries GmbH, Max-Eyth-Straße 10, 71364 Winnenden, Germany.
SYMBOLS
CAUTION! WARNING! DANGER!
Remove the battery pack before starting any work
on the machine.
Please read the instructions carefully before
starting the machine.
Always wear goggles when using the machine.
Wear gloves!
Wear ear protectors!
Keep hands away!
Do not dispose electric tools, batteries/
rechargeable batteries together with household
waste material.
Electric tools and batteries that have reached the
end of their life must be collected separately and
returned to an environmentally compatible
recycling facility.
Check with your local authority or retailer for
recycling advice and collection point.
n
0
No-load speed
V
Volts
Direct current
European Conformity Mark
British Confomity Mark
Ukraine Conformity Mark
EurAsian Conformity Mark
ENGLISH