Owner's manual
17
16
< 30°
< 30°
< 30°
TECHNICAL DATA
Type Cordless Angle Grinder
Production code 4811 85 01
XXXXXX MJJJJ
Battery voltage 18 V ⎓
Rated speed 8500 min
-1
Thread of work spindle M14
D=Grinding disc diameter max.
d=Grinding disc hole diameter
115 mm
22,2 mm
b=Grinding disc thickness max.
6 mm
b=Cutting disc thickness max. / min.
3 mm / 1 mm
D=Sanding disc diameter max.
115 mm
D=Wiring brush diameter max.
75 mm
Weight according EPTA-Procedure 01/2014
(Li-Ion 2,0 Ah ... 12,0 Ah)
2,4 ... 3,4 kg
Recommended Ambient Operating Temperature -18 ... +50 °C
Recommended battery types M18B...; M18HB...
Recommended charger M12-18...; M1418C6
Noise information: Measured values determined according to EN 60745.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level / Uncertainty K
Sound power level / Uncertainty K
Wear ear protectors!
82,6 dB (A) / 3 dB (A)
93,6 dB (A) / 3 dB (A)
Vibration information: Vibration total values (triaxial vector sum)
determined according to EN 60745.
Vibration emission value a
h
/ Uncertainty K
Surface grinding
Disc sanding
4,33 m/s
2
/ 1,5 m/s
2
1,62 m/s
2
/ 1,5 m/s
2
For other applications, e.g. Abrasive Cutting-Off Operations or Wire Brushing other vibration values could occur.
WARNING!
The vibration and noise emission level given in this information sheet has been measured in accordance with a standardized test given in
EN 60745 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration and noise emission level represents the main applications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained, the vibration and noise emission may differ. This may signicantly increase the
exposure level over the total working period.
An estimation of the level of exposure to vibration and noise should also take into account the times when the tool is switched off or when it
is running but not actually doing the job. This may signicantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the effects of vibration and/or noise such as: maintain the tool and the
accessories, keep the hands warm, organization of work patterns.
WARNING! Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in electric
shock, re and/or serious injury.
Save all warnings and instructions for future reference.
ANGLE GRINDER SAFETY WARNINGS
Safety Warnings Common for Grinding, Sanding, Wire Brus-
hing or Abrasive Cutting-Off Operations:
a) This power tool is intended to function as a grinder,
sander, wire brush or cut-off tool. Read all safety warnings,
instructions, illustrations and specications provided with
this power tool. Failure to follow all instructions listed below may
result in electric shock, re and/or serious injury.
b) Operations such as polishing are not recommended to be
performed with this power tool. Operations for which the power
tool was not designed may create a hazard and cause personal
injury.
c) Do not use accessories which are not specically designed
and recommended by the tool manufacturer. Just because the
accessory can be attached to your power tool, it does not assure
safe operation.
d) The rated speed of the accessory must be at least equal to
the maximum speed marked on the power tool. Accessories
running faster than their rated speed can break and y apart.
e) The outside diameter and the thickness of your acces-
sory must be within the capacity rating of your power tool.
Incorrectly sized accessories cannot be adequately guarded or
controlled.
f) Threaded mounting of accessories must match the grinder
spindle thread. For accessories mounted by anges, the
arbour hole of the accessory must t the locating diameter of
the ange. Accessories that do not match the mounting hardware
of the power tool will run out of balance, vibrate excessively and
may cause loss of control.
M18 FSAG115XB