Owner's manual
23
22
ENGLISH
a) Do not use excessively oversized sanding disc paper.
Follow manufacturers recommendations, when selecting san-
ding paper.
a) Be aware that wire bristles are thrown by the brush even
during ordinary operation. Do not overstress the wires by
applying excessive load to the brush. The wire bristles can
b) If the use of a guard is recommended for wire brushing, do
not allow any interference of the wire wheel or brush with the
guard.
ADDITIONAL SAFETY AND WORKING INSTRUCTIONS
circuit!
SPECIFIED CONDITIONS OF USE
RESIDUAL RISK
•
•
•
•
NOTES FOR LI-ION BATTERIES
Use of Li-Ion batteries
Battery protection for Li-Ion batteries
Transporting Lithium Batteries
WORKING INSTRUCTIONS
ENGLISH
f) Threaded mounting of accessories must match the grinder
g) Do not use a damaged accessory. Before each use inspect
the accessory such as abrasive wheels for chips and cracks,
backing pad for cracks, tear or excess wear, wire brush for
loose or cracked wires. If power tool or accessory is dropped,
inspect for damage or install an undamaged accessory. After
inspecting and installing an accessory, position yourself and
bystanders away from the plane of the rotating accessory and
run the power tool at maximum no-load speed for one minute.
h) Wear personal protective equipment. Depending on appli-
cation, use face shield, safety goggles or safety glasses. As
appropriate, wear dust mask, hearing protectors, gloves and
workshop apron capable of stopping small abrasive or work-
piece fragments.
i) Keep bystanders a safe distance away from work area.
Anyone entering the work area must wear personal protective
equipment.
j) Hold the power tool by insulated gripping surfaces only,
when performing an operation where the cutting accessory
may contact hidden wiring.
k) Never lay the power tool down until the accessory has come
to a complete stop.
l) Do not run the power tool while carrying it at your side. Acci-
m) Regularly clean the power tool’s air vents.
o) Do not use accessories that require liquid coolants. Using
Kickback and Related Warnings
-
-
body and arm to allow you to resist kickback forces. Always
use auxiliary handle, if provided, for maximum control over
kickback or torque reaction during start-up. The operator can
b) Never place your hand near the rotating accessory. Acces-
c) Do not position your body in the area where power tool will
move if kickback occurs.
d) Use special care when working corners, sharp edges etc.
Avoid bouncing and snagging the accessory. Corners, sharp
e) Do not attach a saw chain woodcarving blade or toothed saw
blade.
Off Operations:
a) Use only wheel types that are recommended for your power
b) The grinding surface of the centre depressed wheels must
be mounted below the plane of the guard lip.
c) The guard must be securely attached to the power tool and
positioned for maximum safety, so the least amount of wheel
is exposed towards the operator.
d) Wheels must be used only for recommended applications.
For example: do not grind with the side of cut-off wheel. Abra
-
size and shape for your selected wheel.
f) Do not use worn down wheels from larger power tools.
Operations:
a) Do not “jam” the cut-off wheel or apply excessive pressure.
Do not attempt to make an excessive depth of cut. Overstres-
b) Do not position your body in line with and behind the rota-
ting wheel.
c) When wheel is binding or when interrupting a cut for any
reason, switch off the power tool and hold the power tool
motionless until the wheel comes to a complete stop. Never
attempt to remove the cut-off wheel from the cut while the
wheel is in motion otherwise kickback may occur. Investigate
d) Do not restart the cutting operation in the workpiece. Let
the wheel reach full speed and carefully re-enter the cut. The
e) Support panels or any oversized workpiece to minimize the
risk of wheel pinching and kickback.
f) Use extra caution when making a “pocket cut” into existing
walls or other blind areas.