Owner's manual

Deutsch
1515
GB
English
TECHNICAL DATA
Press device
M18 ONEBLHPT
Production code 4777 60 02 ...
... 000001-999999
Frequency band(s) of Bluetooth 2402 - 2480 MHz
Radio-frequency power 1,8 dBm
Bluetooth version 4.2 BT signal mode
Battery voltage 18 V
Power consumption 450 W
Nominal force 32 kN
Compression range:
Ø Plastics & Composite pipes
Ø Metal until
63 mm (110 mm)
54 mm (108 mm)
dep. on system
Weight according EPTA-Procedure 01/2014
(Li-lon 2,0 Ah ... 12,0 Ah) 2,9 ... 3,9 kg
Weight
(M18 ONEBLHPT / Li-Ion 2.0 Ah / J18-Th14) 4,7 kg
Noise information
Measured values determined according to EN60745. Typically, the
A-weighted noise levels of the tool are:
Sound pressure level (Uncertainty
K=3dB(A))
75 dB (A)
Sound power level (Uncertainty K=3dB(A)) 86 dB (A)
Wear ear protectors!
Vibration information
Vibration total values (triaxial vector sum) determined according
to EN60745
Vibration emission value a
h
<2,5 m/s
2
Uncertainty K= 1,5 m/s
2
WARNING!
The vibration and noise emission level given in this information
sheet has been measured in accordance with a standardized test
given in EN60745 and may be used to compare one tool with
another. It may be used for a preliminary assessment of exposure.
The declared vibration and noise emission level represents the
main applications of the tool. However if the tool is used for die-
rent applications, with dierent accessories or poorly maintained,
the vibration and noise emission may dier. This may signicantly
increase the exposure level over the total working period.
An estimation of the level of exposure to vibration and noise should
also take into account the times when the tool is switched o or
when it is running but not actually doing the job. This may signi-
cantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from
the eects of vibration and/or noise such as: maintain the tool
and the accessories, keep the hands warm, organization of work
patterns.
WARNING Read all safety warnings and all instruc-
tions. Failure to follow the warnings and instructions may result in
electric shock, re and/or serious injury.
Save all warnings and instructions for future reference.
PRESS DEVICE SAFETY WARNINGS
Use protective equipment. Always wear goggles when using the
machine. The use of protective clothing is recommended, such as
dust mask, protective gloves, sturdy non-slip footwear, helmet and
ear defenders.
Never hold your ngers or other body parts in the working area of
the cylinder or the press jaws.
Do not hold the jaw levers with your hands during the pressing
operation.
Press tools and press devices must only be used by trained
personnel.
Check the press tools and press devices for cracks and other signs of
wear before each use.
Only use press tools and press devices that are in perfect technical
condition.
Have damage repaired immediately by an authorised workshop.
The machine may only be used with a press jaw inserted into it.
In the event of problems during the pressing process, press the
Emergency Stop button immediately and release the ON switch.
The valve will open and the piston will return to its initial position.
Compliance with the specied service work and service intervals is
mandatory.
Remove the battery pack before starting any work on the
appliance.
WORKING INSTRUCTIONS
Use only system-compatible press ttings and press jaws designed
for them.
Consult the documents provided by the system supplier for hand-
ling and assembly instructions for ttings and pipes.
Check whether the nominal width of the press tting corresponds
to the nominal width of the press jaws.
Make sure that the press jaw is fully closed when pressing is
complete.
Imperfect pipe joints must be compressed again using a new
tting.
After nishing the work, check the installation with appropriate
testing equipment and assure that it is leakproof!
The press device is not suitable for continuous operation. Following
30 minutes of continuous operation, a short break of at least 15
minutes must be taken to allow the device to cool down.
SPECIFIED CONDITIONS OF USE
The devices and the press jaws are designed exclusively for the
press-tting of pipes and ttings for which the relevant press jaws
are intended.
These press devices are intended exclusively for use with press jaws
approved by Milwaukee in agreement with the system supplier.
ONEKEY™
To learn more about the ONE-KEY functionality of this device,
please refer to the Quick Start guide included with this product or
go to http://www.milwaukeetool.com/one-key
To download the ONE-KEY app, visit the App Store or Google Play
from your smart device.
We considered the result to be within our minimum acceptable
performance level according to EN301489-1/ EN301489-17.