Owner's manual

29
BATTERIES
Battery packs which have not been used for some time should be
recharged before use.
Temperatures in excess of 50°C (122°F) reduce the performance of the
battery pack. Avoid extended exposure to heat or sunshine (risk of
overheating).
The contacts of chargers and battery packs must be kept clean.
For an optimum life-time, the battery packs have to be fully charged,
after use.
To obtain the longest possible battery life remove the battery pack from
the charger once it is fully charged.
For battery pack storage longer than 30 days: Store the battery pack
where the temperature is below 27°C and away from moisture Store the
battery packs in a 30% - 50% charged condition
TRANSPORTING LITHIUM BATTERIES
Lithium-ion batteries are subject to the Dangerous Goods Legislation
requirements.
Transportation of those batteries has to be done in accordance with local,
national and international provisions and regulations.
The user can transport the batteries by road without further require-
ments.
Commercial transport of Lithium-Ion batteries by third parties is subject
to Dangerous Goods regulations. Transport preparation and transport
are exclusively to be carried out by appropriately trained persons and the
process has to be accompanied by corresponding experts.
When transporting batteries:
Ensure that battery contact terminals are protected and insulated to pre-
vent short circuit. Ensure that battery pack is secured against movement
within packaging. Do not transport batteries that are cracked or leak.
Check with forwarding company for further advice
BATTERY PACK PROTECTION
In extremely high torque, binding, stalling and short circuit situations
that cause high current draw, the tool will stop for about 2 seconds and
then the tool will turn OFF. To reset, remove the battery pack from the
tool and replace it.
Under extreme circumstances, the internal temperature of the battery
pack could raise too much. If this happens, the fuel gauge will ash until
the battery pack cooled down. After the lights go o, the work may
continue.
Place the battery on the charger to charge and reset it.
MAINTENANCE
Remove the battery pack before starting any work on the appliance.
Be sure to disconnect the tool from the power supply before attaching or
removing the saw blade.
Replace the table insert when worn
Clean tool and guarding system with dry cloth.
The ventilation slots of the machine must be kept clear at all times.
Use only Milwaukee accessories and Milwaukee spare parts. Should
components need to be replaced which have not been described, please
contact one of our Milwaukee service agents (see our list of guarantee/
service addresses).
If needed, an exploded view of the tool can be ordered. Please state the
Article No. as well as the machine type printed on the label and order the
drawing at your local service agents or directly at: Techtronic Industries
GmbH, Max-Eyth-Straße10,
71364Winnenden, Germany.
SYMBOLS
CAUTION! WARNING! DANGER!
Remove the battery pack before starting any work on the
appliance.
Please read the instructions carefully before starting the
machine.
Always wear goggles when using the machine.
Wear ear protectors!
Wear gloves!
Always keep hands away from the path of the saw blade.
Never expose tool to rain.
Do not stare into beam.
EDITION : A
xxxxxxxxxxxxxxxxxx
29x11.6(4-R0.5)mm
(
± 0.2mm)
g
50# UL silver foil
Matt PP coating
Permanent Acrylic Removeable Acrylic
Other
CM001xxxxx
ECN-CM01xxxx
River Liu
2018.June.22
01
Black + Pantone Yellow C
Total: 2C
Laser warning label_for SMS216 & M18 MS216 EMEA versionDescription:
MODEL NO
WEIGHT
VENDOR
PART NO
ITEM ID
REV.
SIZE
SCALE : 100%
Approved By:
Graphic Designer
Approved By:
Electrical Engineer
Approved By:
Quality Assurance
Approved By:
Chief Designer / Eng, Manager
MATERIAL
ECN#
CORE:
LAMINATION:
ADHESIVE:
COLOR
LASER
1M
29mm
11.6mm
Pantone
Yellow C
Do not view directly into beam with optical
instruments (binocular, telescope).
This product corresponds to the laser class 1
in accordance with EN 60825-1:2014 .
Do not dispose electric tools, batteries/rechargeable batte-
ries together with household waste material. Electric tools
and batteries that have reached the end of their life must
be collected separately and returned to an environmentally
compatible recycling facility. Check with your local authori-
ty or retailer for recycling advice and collection point.
V
Voltage
Direct Current
n
0
No-load speed
Saw blade dia. x hole dia
European Conformity Mark
British Conformity Mark
Ukraine Conformity Mark
EurAsian Conformity Mark
English
GB