Operator's Manual

ManualsBrandsMilwaukee ManualsJobsite Clean UpM18 FUEL™ HAMMERVAC™ 26 mm Dedicated Dust Extractor (Tool Only)

SYMBOLOGY

Volts

Direct Current

Read Operator's Manual

SPECIFICATIONS

Cat. No. ................................................. M18 FDEX

Cat. No. ............................................... M18 FPDEX

Do not dispose of electric tools

together with household waste

material. Electric tools and electronic

equipment that have reached the end

of their life must be collected

separately and returned to an

environmentally compatible recycling

facility.

Regulatory Compliance Mark (RCM).

This product meets applicable

regulatory requirements.

Wear safety glasses.

For use only with M18 FH M18 FUEL™ 26 mm

SDS PLUS Rotary Hammer

For use only with M18 FHP M18 FUEL™

28 mm SDS PLUS Rotary Hammer

Min Bit Diameter ............................................ 5 mm

Recommended Ambient

Large Nozzle Max Bit Diameter................ 31.7 mm

Operating Temperature ................... -17°C to 51°C

Max depth ..................................................152 mm

Dust Box Cat. No .................................. 49902344

ASSEMBLY

1. Turn OFF the tool.

2. Remove the battery pack.

Squeeze the dust box latches.

Pull the dust box away from the HAMMERVAC™.

Removing/Installing the Dust Box

and HEPA Filter

To remove the dust box:

Dust box

port

HEPA

Empty debris by holding away

from the user’s face and tap-

ping dust box into a trash can,

pail, or other suitable

container. For best cleaning

results, connect a vacuum

hose with dust extraction

adaptor (Cat. No. 49901959)

to the dust box port and suc-

tion out debris.

If necessary, pull the HEPA filter away from the

dust box and tap clean. Do not clean with water

or compressed air. After about 1500 holes or loss

of suction, discard and replace HEPA filter (Cat.

No. 49902306).

To install the dust box:

1. Slide the dust box into the body of the

HAMMERVAC™.

2. The dust box latches should snap into place.

NOTE: Do not operate the HAMMERVAC™ without

Installing/Removing Nozzle

Replace the nozzle:

• After drilling about 1500 holes,

• When the bit brush shows signs

of wear,

• When suction is reduced,

• When dust escapes through the

bit brush during use

To replace the Standard

(Cat. No. 14520105 and Large

Cat. No. 14520110) nozzles,

rotate the nozzle release lever

down to the open position and

pull out nozzle from the lower nozzle assembly.

Slide the new nozzle into the lower nozzle assembly

and rotate the nozzle release lever up to the closed

position.

Dove tail slot

Front depth

bracket

Bit depth

gauge button

Tabs

Rear depth

bracket

screws

Rear depth

bracket

Removing/Installing the Depth Stop

To remove the depth stop:

depth bracket with a philips screwdriver.

1. Turn OFF the tool.

2. Remove the battery pack.

3. Remove screws from left and right side of rear

Remove front

NOTE: Use a

depth bracket by pulling up on it.

snap, if needed.

To install the depth stop:

1. Place the rear depth bracket into the slot on the

top of the dedicated dust extractor.

2. Insert screws into the left and right side of rear

depth bracket with a philips screwdriver.

3. Insert front depth bracket into dove tail slot on

nozzle base and push down until snapped into

place.

WARNING

Only use accessories specifically

recommended for this tool.

Others may be hazardous. To reduce the risk of

injury, always remove the battery pack before

removing the dust box. Do not use tool without

dust box and HEPA filter in place.

CAUTION

Keep filter clean. Efficiency of the

HAMMERVAC™ is largely

dependent on the filter. A dirty filter will reduce

the air flow and overall efficiency of the system.

Do not clean with water or compressed air.

Remove from dust box and tap clean.

Nozzle Max Bit Diameter ............................. 16 mm