Operator's Manual

4
10. Close the jaws and securely tighten the socket
screws.
OPERATION
WARNING
To reduce the risk of explosion,
electric shock and property
damage, do not use on live electrical lines. Tool
is NOT insulated. Contact with a live circuit
could result in severe injury or death. Turn off power
before making a cut. Never cut gas or water lines.
Keep hands away from all cutting edges and
moving parts. Laceration and amputation
can occur.
Always remove battery pack before changing or
removing accessories. Only use accessories spe-
hazardous.
To reduce the risk of injury, wear safety goggles or
glasses with side shields. Always use a side handle
when using this tool.
Cutting
Before cutting, ensure blades are properly installed.
1. Insert the workpiece squarely between the blades.
Do not attempt to make angled cuts as it will dam-
age the workpiece and blades. Ensure the jaws
close completely.
2.
workpiece is straight and centered in the jaws.
Keep hands away from blades.
3. Pull and hold the trigger through the operation.
When the cut is complete or the tool shuts off,
release the trigger. An LED will light when the
trigger is pulled. NOTE: Workpiece may move
slightly during the cut.
notice of the blade orientation so the new blade
can be installed the same way.
5. Remove the locking thumb screw from the back
of the retaining pin. Push the blade pin out.
6. Slide the rear blade out of the jaws. NOTE: Take
notice of the blade orientation so the new blade
can be installed the same way.
7.
and the bevels face away from each other, like a
pair of scissors.
8. Insert the new rear blade and push in the retaining
.wercs bmuht gnikcol eht nethgit dnah dna tresnI .nip
9. Insert the front blade and hand tighten the socket
screws.
SPECIFICATIONS
Cat. No. ...............................................M18 HCC45
Volts .............................................................. 18 DC
Battery Type .................................................M18™
Charger Type ................................................M18™
Recommended Ambient
Operating Temperature ....................
-18°C to 51°C
(0°F to 125°F)
Maximum Capacity .................860mm
2
MCM ACSR
Guy Wire: 16mm (5/8")
EHS Guy Wire: 13mm (1/2")
Rebar: 16mm (5/8")
Ground Rod: 16mm (5/8")
ASSEMBLY
WARNING
Recharge only with the charger
-
manual supplied with your charger and battery.
Removing/Inserting the Battery
To remove the battery, push in the release buttons
and pull the battery pack away from the tool.
WARNING
Always remove battery pack before
changing or removing accessories.
To insert the battery, slide the pack into the body
of the tool. Make sure it latches securely into place.
WARNING
recommended for this tool. Others
may be hazardous.
Blades are sharp. Keep hands away from cutting
edge. Laceration can occur.
Installing and Adjusting the Side Handle
1. To install, unscrew the side handle
Collar
Bolt
Housing
Grip
grip completely.
2. Remove the housing from the collar
and bolt.
3. Slide the collar around the neck of
the head.
4. Insert the bolt head into the collar.
5. Fit the housing over the bolt.
6. Screw on the side handle grip.
7. To adjust, unscrew the side handle
grip slightly.
8. Rotate the side handle to the de-
sired position.
9. Tighten the side handle grip se-
curely.
Opening the Jaws
To open the jaws, squeeze the jaw
release levers together. The front jaw
will open and the rear jaw will swing
out.The front jaw will stay open until
the workpiece is inserted.
Changing the Blades
Replace the blades when they become chipped or
damaged. Always replace blades as a set. Use only
1. Pull trigger for 1 second to slightly extend the rear
blade.
2. Remove the battery pack.
3. Using a 5 mm hex wrench, remove the socket
screws holding the front blade.
4. Press the jaw release levers to open the jaws
and carefully remove the front blade. NOTE: Take
MILWAUKEE
®
Replacement Blades..................Cat. No. 49162775