Operator's Manual

6
Cutting without Remote
 Before cutting, ensure blades are properly installed.
 The tool can be set on the ground or hand held
during use. To set the tool on the ground, rotate
the cutting head 180° to use the front handle as a
handles, as shown.
 Insert the workpiece squarely between the blades.
Do not attempt to make angled cuts as it will dam-
age the workpiece and blades.
 Ensure the remote cut switch is turned to OFF.
1.
through the operation. When the cut is complete or
the tool shuts off, release the trigger. A LED will
light when the trigger is pulled. NOTE: Workpiece
may move slightly during the cut.
2. When the cut is complete, pull the release trigger
to open the blades.
WARNING
To reduce the risk of injury, only
cut recommended materials for the
cut other materials.
Cutting Tips
 Cut farther in from the end of the material to avoid
crooked cuts.
 Do not attempt angled cuts as it will damage the blades.
Hold the material squarely between the blades.
 Cut clean material to extend the blade life. Wipe dirt
and debris from material and blades before begin-
ning the cut.
 Use the trigger lock to lock-off the trigger when the
tool is not in use.
Jammed Blades
Dirt and debris can cause the blades to become
jammed together after a cut. If the blades do not
open when the release trigger is pulled:
1. Press and hold the release trigger to ensure the
tool has reset.
2. Remove the battery pack.
3. While holding in the release trigger, use a rubber
mallet to tap the blade retainer until the blades open.
4. Clean any dirt and debris from the blades before
starting another cut.
ONE-KEY™
To learn more about the ONE-KEY functionality for
this tool, please reference the Quick Start guide included
with this product or go to milwaukeetools.com.au/
One-Key or milwaukeetools.co.nz/One-key.
or Google Play from your smart device.
MAINTENANCE
WARNING
To reduce the risk of injury, always
unplug the charger and remove the
battery pack from the charger or tool before
performing any maintenance. Never disassemble
the tool, battery pack or charger. Contact a
MILWAUKEE
®
service facility for ALL repairs.
Maintaining Tool
Keep your tool, battery pack and charger in good
repair by adopting a regular maintenance program.
Inspect your tool for issues such as undue noise,
misalignment or binding of moving parts, breakage of
parts, or any other condition that may affect the tool
operation. Return the tool, battery pack, and charger
to a MILWAUKEE
®
service facility for repair. After six
months to one year, depending on use, return the
tool, battery pack and charger to a MILWAUKEE
®
service facility for inspection.
If the tool does not start or operate at full power with
a fully charged battery pack, clean the contacts on
the battery pack. If the tool still does not work prop-
erly, return the tool, charger and battery pack, to a
MILWAUKEE
®
service facility for repairs.
NOTE: Refer to your ONE-KEY App for additional
service interval information.
Cutting Head and Blades
Inspect the cutting head and blades for cracks or
damage. Do not use damaged cutting head or blades.
Replace the blades when they become chipped or
damaged.
Service Interval
Refer to the ONE-KEY App for information regard-
Return the tool to a MILWAUKEE
®
service facility for
all repairs and maintenance.
WARNING
This device contains a
lithium button/coin cell
battery. A new or used battery can
cause severe internal burns and lead
to death in as little as 2 hours if swal-
lowed or enters the body. Always secure the
battery cover. If it does not close securely, stop
using the device, remove the batteries, and keep
it away from children. If you think batteries may
have been swallowed or entered the body, seek
immediate medical attention.
Internal Battery
An internal battery is used to facilitate full ONE-KEY™
functionality.
To replace the battery:
1. Remove the battery pack.
2. Remove the screw and open the battery door.
3. Remove the old battery.
4. Insert the new battery (3V CR2032), with the posi-
tive side facing up.
5. Close the battery door and tighten the screw
securely.
To download the ONE-KEY app, visit the App Store
WARNING
damage, do not use on live electrical lines. Tool is
NOT insulated. Contact with a live circuit could
result in severe injury or death. Turn off power
before making a cut. Never cut gas or water lines.
To reduce the risk of explosion,
electric shock and property