Operator's Manual

6
ONE-KEY™ Indicator
Solid Blue
Blinking Blue
Tool is actively communicating with
the ONE-KEY™ app.
Blinking Red
OPERATION
Tool is in security lockout and can
be unlocked by the owner via the
ONE-KEY™ app.
WARNING
Selecting Mode
The pump features three modes of operation:
Auto-Dump mode unloads pump pressure as
soon as 10,000 psi is reached.
Hold Pressure mode holds pressure until the
manual release button is pushed or the retract button
is pushed on the remote.
Wireless mode allows the user to activate the
pump via bluetooth signal. The pump will run to full
pressure and then release. The remote must be re-
attached for the next application.
ONE-KEY™
To reduce the risk of injury, always wear proper
eye protection marked to comply with ANSI Z87.1.
Before using:
•
•
•
or damage. Replace worn, damaged, or missing
components with manufacturer's replacement parts.
WARNING! Do not use hands to check for leaks.
High pressure oil easily punctures skin, causing
serious injury, gangrene, or death. If injured, seek
medical help immediately to remove oil.
• Ensure pump is in the desired mode of operation.
Ensure pump is below the maximum tilt angle.
• Follow accessory manufacturers' installation instruc-
tions. Other uses may cause damage to the tool,
accessories, and workpiece.
• Bleed the system if necessary.
To operate with the remote cable-connected to
the pump:
6. Press and hold the ad-
1. Depressurize the tool by holding down the manual
2. Insert the battery pack.
3. Connect the hose coupler to the pump coupler.
4. Connect the tool head to the hose.
5. Press and select the preferred mode of operation
between auto-dump and hold pressure .
vance button on the
remote.
1
sec
7. If in auto-dump mode ,
the pump will release
pressure as soon as
10,000 psi is reached.
and the indicator will
light.
8. Press the retract button
for one second.
Light
Indicator
Solid Green Tool reached full pressure.
Solid Red Tool did not reach full pressure.
Continuous
Flashing
Red/Green
(after Solid
Green or
Solid Red)
Short
Flashing
Red/Green
To operate in Wireless mode:
1.
2. Insert the battery pack.
3. Connect the hose coupler to the pump coupler.
4. Connect the tool head to the hose.
5. Disconnect the remote from the cable and remove
it from the pump.
To learn more about the ONE-KEY™ functionality
for this tool, please reference the Quick Start guide
included with this product or go to
www.milwaukeetools.com.au/one-key To download
the ONE-KEY™ app, visit the App Store or Google
Play from your smart device.
To reduce the risk of arc
flash, electric shock and
property damage, work on de-energized
lines when possible. Tool is not insulated.
Should work on energized lines be required,
ensure all proper precautions have been taken
first.
Check the oil level and adjust if necessary. Low oil
may result in injury or property damage. For best
performance, always use Hydraulic Oil to refill the
reservoir.
Tool has reached its service interval
(20,000 crimps). Red/Green flashing
will begin after the solid Red or Green
indicator for the operation is displayed.
MILWAUKEE
®
recommends that the
tool be inspected and preventative
maintenance completed. Return tool to
a MILWAUKEE
®
service facility.
Tool has malfunctioned and can no
longer be used until it is serviced.
Return tool to a MILWAUKEE
®
service
facility.
NOTE: If the indicator shows red, check the oil
levels and ensure that there are no leaks in the
attachments. Confirm that all connections are
secure and the attachments are secure. Repeat the
steps under “Operation”. If the problem persists,
return the tool to a MILWAUKEE
®
service facility.
De-pressurize the tool by holding down the
manual release button for five seconds.
Wireless mode is active and ready
to be configured via the ONE-KEY™
app.