Operator's Manual

3
Adjusting the Pivot Head
Cat. No. 2735-20, 49-24-0145 and 49-24-0146 -
The pivot head can pivot to a range of 90°; with
detents every 15° (every 10° for the 2735-20).
Pivot head to desired position. Allow the detent
to snap into place. Do not forcibly pivot the head.
Cat. No. 49-24-0171,
49-24-0187, and
49-24-0185 - The pivot
head can pivot to a range
of 135°; with detents
every 10°. Pivot head to
desired position. Allow
the detent to snap into
place. Do not forcibly
pivot the head.
WARNING To reduce the
risk of injury and damage, never insert bulbs
other than the recommended MILWAUKEE
replacement bulb in the bulb socket. Other
bulbs will over heat!
WARNING To reduce the
risk of injury, DO NOT operate work light
without bezel assembly in place. Bulb does
get hot. Always remove battery pack before
changing or removing bulbs. Always allow
the work light to cool for at least 10 minutes
before replacing the bulb.
OPERATION
To turn on the work light, press the ON/OFF but-
ton. To turn off the work light, press the ON/OFF
button again.
Hook
Cat.No. 2735-20,
49-24-0185,
49-24-0187 and
49-24-0171)
To use the hang-
ing hook, press in
the hook joint. Pull
the hook out.
Replacing the Bulb (Cat. No. 49-24-0145,
49-24-0171, and 49-24-0185)
NOTE: Cat. No. 49-24-0146, 2735-20, and
49-24-0187 use an LED bulb that cannot be re-
placed. Bezel can not be removed. Attempting to
remove the bezel will damage tool.
1. Remove battery pack before changing bulb.
2. Unscrew the bezel assembly on pivot head by
turning counterclockwise.
3. Remove the bezel assembly.
4. For Cat. No. 49-24-0185
and 49-24-0171, pull
the aluminum heat sink
forward.
5. Gently rotate bulb coun-
ter clockwise and pull
out.
To install new bulb, follow
above directions in reverse.
Cleaning
Keep tool handles clean, dry and free of oil or
grease. Use only mild soap and a damp cloth to
clean the tool, battery pack and charger since cer-
tain cleaning agents and solvents are harmful to
plastics and other insulated parts. Some of these
include gasoline, turpentine, lacquer thinner, paint
thinner, chlorinated cleaning solvents, ammonia
and household detergents containing ammonia.
Never use flammable or combustible solvents
around tools.
Maintain Work Light
Keep your work light, battery pack and charger in
good repair by adopting a regular maintenance
program. If the work light does not work properly,
return the work light to a MILWAUKEE service
facility for repairs.
MAINTENANCE
WARNING To reduce the
risk of injury, always unplug the charger and
remove the battery pack from the charger
or tool before performing any maintenance.
Never disassemble the tool, battery pack or
charger. Contact a MILWAUKEE service facility
for ALL repairs.
WARNING To reduce the risk
of personal injury and damage, never immerse
your tool, battery pack or charger in liquid or
allow a liquid to ow inside them.
ACCESSORIES
For a complete listing of accessories refer to your
MILWAUKEE Electric Tool catalog or go online
to www.milwaukeetool.com. To obtain a catalog,
contact your local distributor or a service center.
WARNING Always remove
battery pack before changing or removing
accessories. Only use accessories speci-
cally recommended for this tool. Others may
be hazardous.
Pull
out
Press
Bulb
Aluminum
heat sink
Pull
forward
Cat. No.
49-24-0185,
49-24-0171
NOTE: Use a soft cloth when installing bulbs. Direct
contact with oils or other contamination can shorten
the life of bulbs.
On Cat. No. 49-24-0171 and 49-24-0185, a spare
bulb can be stored behind the aluminum heat sink.
See “Specications” chart for proper replacement
bulbs. See your nearest MILWAUKEE Retailer or
Service Center to obtain replacement bulbs.