OPERATOR'S MANUAL MANUEL de L'UTILISATEUR MANUAL del OPERADOR Cat. No. / No de cat. 2873-20 M18 FUEL™ ANGLER™ PULLING FISH TAPE RUBAN À FILS DE TIRAGE ANGLER™ M18 FUEL™ CINTA PASADORA PARA JALAR M18 FUEL™ ANGLER™ WARNING To reduce the risk of injury, user must read and understand operator's manual. AVERTISSEMENT Afin de réduire le risque de blessures, l'utilisateur doit lire et bien comprendre le manuel. ADVERTENCIA Para reducir el riesgo de lesiones, el usuario debe leer y entender el manual.
•Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. •Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. •Dress properly. Do not wear loose clothing or jewelry. Keep your hair and clothing away from moving parts. Loose clothes, jewelry or long hair can be caught in moving parts.
•When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire. •Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help.
General Operation ASSEMBLY Recharge only with the charger 1. Install the battery pack. WARNING specified for the battery. For spe- 2. Support fish tape during use. cific charging instructions, read the operator’s 3. To feed the conduit run, move the control switch to the feed position and pull the trigger. manual supplied with your charger and battery. 4. To vary the speed, increase or decrease pressure Removing/Inserting the Battery on the trigger.
MAINTENANCE reduce the risk of injury, always WARNING To unplug the charger and remove the SERVICE - CANADA Milwaukee Tool (Canada) Ltd 1.800.268.4015 battery pack from the charger or tool before performing any maintenance. Never disassemble the tool, battery pack or charger. Contact a MILWAUKEE service facility for ALL repairs. Monday-Friday, 7:00 AM - 4:30 PM CST or visit www.milwaukeetool.
LIMITED WARRANTY - MEXICO, RÈGLES DE SÉCURITÉ GÉNÉRALES CENTRAL AMERICA & CARIBBEAN RELATIVES AUX OUTILS ÉLECTRIQUES TECHTRONIC INDUSTRIES' warranty is for 5 years since the original Lire toutes les consignes purchase date. AVERTISSEMENT de sécurité, consignes, This warranty card covers any defect in material and workmanship illustrations et spécifications fournies avec cet outil électrique.
SÉCURITÉ INDIVIDUELLE •Entretenir les outils électriques et les accessoires. Vérifier qu'aucune pièce mobile n'est mal alignée ou bloquée, qu'aucune pièce n'est brisée et s'assurer qu'aucun autre problème risque d'affecter le bon fonctionnement de l'outil. En cas de dommages, faire réparer l’outil avant de l’utiliser. Plusieurs accidents sont causés par des produits mal entretenus. •Garder les outils bien affûtés et propres.
ENTRETIEN PICTOGRAPHIE •Les réparations de l’outil électrique doivent être confiées à un technicien qualifié, utilisant exclusivement des pièces identiques à celles d’origine. Le maintien de la sûreté de l’outil électrique sera ainsi assuré. •Ne jamais effectuer la réparation d’un bloc-piles endommagé. La réparation du bloc-piles doit être réalisée par le fabricant ou les fournisseurs de service agréés uniquement.
MONTAGE DE L'OUTIL Ne recharger la batterie AVERTISSEMENT qu’avec le chargeur spéci- 2. Pour retraire le ruban à fils, pousser le commutateur vers le sens indiqué. 3. Pour verrouiller la gâchette, pousser le commutateur vers le centre. La gâchette ne fonctionnera fié. Pour les instructions de charge spécifiques, pas quand le commutateur de contrôle est réglé lire le manuel d’utilisation fourni avec le chargeur en position de verrouillage. Toujours retirer le et les batteries.
GARANTIE LIMITÉE AUX ÉTATS-UNIS ET AU CANADA ENTRETIEN minimiser les risques AVERTISSEMENT Pour de blessures corporelles, Chaque outil électrique* MILWAUKEE (voir exceptions ci-dessous) est garanti à l’acheteur d’origine uniquement pour être exempt de vices de matériaux et de fabrication.
ADVERTENCIAS DE SEGURIDAD GENERALES PARA LA HERRAMIENTA ELÉCTRICA Lea todas las advertencias ADVERTENCIA de seguridad, instrucciones, Cette garantie s’applique aux produits vendus aux États-Unis et au Canada uniquement. Veuillez consulter la rubrique Centre SAV Milwaukee, dans la section Pièces et Services du site Web de MILWAUKEE, à l’adresse www.milwaukeetool.
SEGURIDAD PERSONAL •Almacene las herramientas eléctricas que no se estén utilizando fuera del alcance de los niños y no permita que personas que no estén familiarizadas con la herramienta eléctrica o con estas instrucciones la utilicen. Las herramientas eléctricas son peligrosas en manos de usuarios sin capacitación. •Dé mantenimiento a las herramientas eléctricas y accesorios.
MANTENIMIENTO SIMBOLOGÍA •Lleve su herramienta eléctrica a servicio con un técnico calificado que use únicamente piezas de reemplazo idénticas. Esto asegurará que la seguridad de la herramienta eléctrica se mantenga. •Nunca dé servicio a baterías dañadas. Únicamente el fabricante o proveedores de servicio autorizados deben dar servicio a las baterías.
ENSAMBLAJE la batería sólo con ADVERTENCIA Recargue el cargador especificado 2. Para retraer la cinta pasadora, oprima el interruptor de control en la dirección mostrada. 3. Para bloquear el gatillo, empuje el interruptor de control a la posición central. El gatillo no para ella. Para instrucciones específicas sobre funcionará mientras el interruptor de control esté cómo cargar, lea el manual del operador suminen posición de bloqueado. Siempre extraiga la istrado con su cargador y la batería.
MANTENIMIENTO reducir el riesgo de una ADVERTENCIA Para lesión, desconecte siempre GARANTÍA LIMITADA - E.U.A. Y CANADÁ Cada herramienta eléctrica* de MILWAUKEE (ver excepciones a continuación) está garantizada para el comprador original únicamente de que no tenga material y mano de obra defectuosos.
PÓLIZA DE GARANTÍA - VALIDA SOLO PARA MÉXICO, AMÉRICA CENTRAL Y EL CARIBE La garantía de TECHTRONIC INDUSTRIES es por 5 años a partir de la fecha original de compra. Esta tarjeta de garantía cubre cualquier defecto de material y mano de obra en ese Producto. Para hacer válida esta garantía, presente esta tarjeta de garantía, cerrada/sellada por el distribuidor o la tienda donde compró el producto, al Centro de Servicio Autorizado (ASC).