Use and Care Manual

10
Oiling the Cable Feed Bearings
Keep all exposed, moving, and rotating parts cleaned
properly oiled after each use.
1. Unarm the machine.
Nose of Cable Feed
Bearings
2. Press the quick release
button.
3. Use a hose to clean out the
cable feed with clean water
to remove contaminants.
Drain the drum completely.
4. Move the cable feed handle
to the left and apply a pen-
etrating oil, like WD-40
®
,
into the nose of the cable
feed directly onto all three
bearings. Su󰀩ciently cover all the bearing seals.
5. Move the cable feed handle to the right and repeat.
6. Press the ratchet lever down and then feed and
retract the cable 1-2 feet multiple times to work
the oil around.
7. Repeat after each use.
Cleaning Cables and Drums
The cable and drum should be thoroughly ushed with
water after every use to prevent damaging e󰀨ects of
sediment and drain cleaning compounds. WARNING!
Always wear leather gloves over l atex/rubber gloves
to avoid entanglement. After washing, dry the cable
and drum completely. Then, wipe cable with an oiled
rag before returning it to the drum according to the
instructions in "Cable Installation".
Bound or Knotted Cable
If the cable cannot be pulled from the nose of the
machine, it may be bound or knotted in the drum. To
correct this, the drum may need to be disassembled.
WARNING
Disassembly of the internal drum
when a cable is installed will cause
the cable to unwind quickly and could whip
around uncontrollably, which may result in in-
jury.
Disassembly should only be performed by properly
trained personnel. Contact Milwaukee for assistance.
Replacing the Anchor Cable
Due to the precise torque fastener requirements,
MILWAUKEE recommends contacting a MILWAUKEE
service facility for anchor cable replacement. If eld
replacement is necessary:
To replace the anchor cable:
1. Remove all cable from the drum and disengage it
from the anchor cable. WARNING! Do not open
drum with cable installed.
2. Remove the battery pack.
3. Open the drum latches and remove the drum
cover.
4. Remove the 10 M5 screws holding the front inter-
nal drum to the rear internal drum.
5. Remove the 1/4"-20 nut and bolt holding the an-
chor cable into the drum.
6. Pull the anchor cable out through the nose of the
cable feed by hand. Do not turn on the machine.
7. Feed the new anchor cable in through the nose
of the cable feed by hand. Do not turn on the
machine.
8. Ensure the cable is following the curve of the feed
tube when lying in the drum.
9. Align the anchor cable with the stop and insert the
1/4"-20 bolt. Thread the 1/4"-20 nut onto the bolt
and tighten securely.
10. Realign the front and rear internal drums.
11. Install the 10 M5 screws. Tighten each screw
to 21-23 in-lbs.
WARNING! Overtightening screws can lead to
stripping bosses and early drum failure.
12. Replace the drum cover and latch securely.
Cleaning the Battery and Battery Bay
Keep battery connections and surfaces between the
machine and battery free of debris and materials.
Failure to keep surfaces clean may result in mis-
alignment and/or damage to the battery connection.
Repairs
For repairs, return the machine to the nearest autho-
rized service center.
ACCESSORIES
WARNING
Use only recommended accesso-
ries. Others may be hazardous.
For a complete listing of accessories, go online to
www.milwaukeetool.com or contact a distributor.
SERVICE - UNITED STATES
1-800-SAWDUST (1.800.729.3878)
Monday-Friday, 7:00 AM - 6:30 PM CST
or visit www.milwaukeetool.com
Contact Corporate After Sales Service Technical
Support with technical, service/repair, or warranty
questions.
Email: [e-mail]
Become a Heavy Duty Club Member at
www.milwaukeetool.com to receive important
notications regarding your tool purchases.
SERVICE - CANADA
Milwaukee Tool (Canada) Ltd
1.800.268.4015
Monday-Friday, 7:00 AM - 4:30 PM CST
or visit www.milwaukeetool.ca
LIMITED WARRANTY
USA & CANADA
Every MILWAUKEE MX FUEL™ Product, battery pack, and charger
is warranted to the original purchaser only to be free from defects in
material and workmanship. Subject to certain exceptions, MILWAUKEE
will repair or replace a MX FUEL™ product, battery pack, or charger
which, after examination, is determined by MILWAUKEE to be defec-
tive in material or workmanship for a period of two (2) years after the
date of purchase. Return of the MX FUEL™ product, battery pack,
or charger to a MILWAUKEE factory Service Center location or MIL-
WAUKEE Authorized Service Station, freight prepaid and insured, is
required. For the proper shipping procedure of battery packs, contact
1.800.SAWDUST (1.800.729.3878), or go to www.milwaukeetool.com.
A copy of the proof of purchase should be included with the return
product. This warranty does not apply to damage that MILWAUKEE
determines to be from repairs made or attempted by anyone other
than MILWAUKEE authorized personnel, misuse, alterations, abuse,
normal wear and tear, lack of maintenance, or accidents.
Normal Wear: Many MX FUEL™ products need periodic parts replace-
ment and service to achieve best performance. This warranty does not
cover repair when normal use has exhausted the life of a part including,
but not limited to, assist & drive belts, pulleys, blade anges, vacuum
gaskets, tool free handles, set pins, skis, drive couplers, rubber boots,
auto feed, stabilize blocks, wheels, carrier wheels, cords, o-rings,
seals, bumpers, driver blades, pistons, strikers, lifters, tool holder,
and bumper cover washers.