Owner's manual

ENGLISH
TECHNICAL DATA
Model 4932- 4714 31 4714 30
Tool weight
max.
2,3 kg 2,3 kg
Handle diameter
13 mm 330 mm
2 x 2
460 mm
1 x 1
> 13 - 25
mm
580 mm
2 x 2
640 mm
1 x 1
> 25 - 38
mm
790 mm
2 x 2
610 mm
1 x 1
> 38 - 51
mm
1020 mm
2 x 2
_
> 51 - 64
mm
1250 mm
2 x 2
_
CAUTION! The above chart is for use with
MILWAUKEE attachment accessories,
lanyards, and self-adhering tape. When
using attachment accessories other than
MILWAUKEE attachment accessories with
MILWAUKEE self-adhering tape, follow all
manufacturer's recommended attachment
methods. Secure MILWAUKEE
attachment accessories ONLY with
MILWAUKEE self-adhering tape.
* Do not use on products with a surface
less than the width of the attachment
accessory, or less than 13 mm diameter.
IMPORTANT SAFETY
INSTRUCTIONS
Read and understand all safety
warnings and all instructions.
Failure to follow the warnings and
instructions may result serious injury and
property damage.
Save all warnings and instructions for
future reference.
Do not use for personal fall protection.
For use by trained personnel only. Users
must be knowledgeable in tool safety and
use of tools in "off the ground" situations.
Keep out of the reach of children.
Do not exceed maximum capacity marked
on the lanyard label. Exceeding maximum
capacity may result in serious injury or
death.
Always follow these installation
instructions, including wrapping and length
requirements. Do not use attachment
accessories and self-adhering tape in
temperatures below -40°C or above 65°C.
Use only the continuous length of
self-adhering tape required. Do not splice
two lengths of tape together to make the
required length.
Inspect attachment accessory before each
use. Replace damaged attachment
accessories immediately. Ensure the
fabric is not cut, ripped or frayed, and
stitching is not damaged. Inspect
self-adhering tape before each use.
Remove and re-tape if damaged, loose,
rolled, bunched, wrinkled, or attachment
accessory has moved/slipped along the
tool or out of the tape.
Inspect self-adhering tape if tool has been
dropped or the tape has been impacted.
Replace if tape has ripped, slipped, or
wrinkled. Use only with tools that meet
the attachment accessory specifi cations.
Never modify tools to create attachment
points. Do not attach to tool in a way that
keeps guards, switches or locks from
operating properly. Do not use on tapered
or smooth handled tools where the tape
could slide off the end.
Do not use attachment accessories near
sharp or rough edges that could cut or
fray.
Do not use near caustic substances.
Keep surfaces dry, clean and free from oil
and grease. Dirty surfaces will not allow
self-adhering tape to grip properly.
Do not alter attachment accessories or
use in a manner other than as instructed.
Only connect to tools in the manner
described.
Do not tie knots in attachment accessory
or attach attachment accessory back onto
itself.
Do not increase attachment accessory
length. Do not connect to strings, ropes, or
additional attachment accessories.
Do not secure attachment accessories to
moveable objects, such as ladders or
toolboxes. Moveable objects can pull user
off balance when moved or shifted.
Dropped tools will swing and bounce on
the attachment accessory, which can pull
objects over.
For tools over 2,25 kg, do not secure
lanyard to yourself. Dropped tools will
swing and bounce on the attachment
accessory, which can cause loss of
balance.
Only use attachment accessories on
surfaces wider than the attachment
accessory, or with a diameter wider than
the attachment accessory.
Use Split Ring accessory only in
designated attachment points of the tool.
Do not drill holes or modify tools to use
with split rings.
Inspect Split Ring before each use.
Replace Split Ring if bent or deformed.
Do not secure attachment accessory on
removable parts such as batteries, side
handles, guards, or accessories. Ensure
removable parts are secured to their base
tool before installing attachment
accessory.
After installation, ensure the attachment
accessory does not interfere with the
operation of the product, including guards.
Do not use near moving parts or
machinery. Attachment accessory could
become entangled, causing a serious
hazard.
Do not carry tools by the attachment
accessory.
Do not use to tow objects.
SPECIFIED CONDITIONS OF
USE
Use MILWAUKEE attachment accessories
and self-adhering tape to help reduce the
risks associated with dropped tools.
Do not use this product in any other way
as stated for normal use.
PICTURE DESCRIPTION
A1 D-ring end
A2 Wedge end
B3 D-ring end
B4 Barrel lock (Wedge end)
C5 D-ring end
C6 2nd set of wraps
C7 Overlap
C8 1st set of wraps
C9 Wedge end
OPERATION
1. Select the appropriate attachment
accessory for the tool.
2. Using the technical data chart, cut the
required length of self-adhering tape for
the lanyard/tool combination. CAUTION!
When using energy absorbing lanyards
other than MILWAUKEE energy absorbing
lanyards, use double the length of tape to
attach attachment accessories.
3. Lay the attachment accessory on the
tool so the tape will be at least 2,5 cm