Technical data

ManualsBrandsMilwaukee ManualsPower ToolsWCE 30

Instruction for use

Please read and save these

instruction

Gebrauchsanleitung

Bitte lesen und aufbewahren

Instruction d’utilisation

Prière de lire et de conserver

Istruzioni d’uso

Si prega di leggere le istruzioni e

di conservarle

Instrucciones de uso

Lea y conserve estas

instricciones por favor

Instruções de serviço

Por favor leia e conserve em seu

poder

Gebruiksaanwijzing

Lees en let goed op deze advizen

Brugsanvisning

Vær venlight at læse og opbevare

Bruksanvisning

Vennligst les og ta godt vare på

denne informasjonen

Bruksanvisning

Var god läs och tag tillvara dessa

instruktioner

Käyttöohje

Lue ja säilytö

Kullan∂m k∂lavuzu

Lütfen okuyun ve saklay∂n

Инструкция по

эксплуатации

Пожалуйста, прочтите и

сохраните данную инструкцию

FIN

RUS

WCE 30

Summary of content (9 pages)

PAGE 1
WCE 30 GB Instruction for use Please read and save these instruction D Gebrauchsanleitung F Instruction d’utilisation I Istruzioni d’uso DK Brugsanvisning N Bruksanvisning S Bruksanvisning Bitte lesen und aufbewahren Prière de lire et de conserver Vær venlight at læse og opbevare Vennligst les og ta godt vare på denne informasjonen Var god läs och tag tillvara dessa instruktioner Si prega di leggere le istruzioni e di conservarle FIN Käyttöohje E Instrucciones de uso TR Kullan∂m k∂lav
PAGE 2
a (mm) b (mm) c (mm) m/sec 125 150 2,5 2,5 22,2 22,2 80 80 125 150 2,5 2,5 22,2 22,2 80 80 WCE 30 Id.-No.
PAGE 3
You demand the best and buy quality - quality provided by Milwaukee. We have built for you a reliable and lasting tool. Working effectively and without endangering your health is only possible if this instruction for use is read carefully before first using the tool. We want to satisfy our customers and would like you to buy again Electric Power Tools from Milwaukee.
PAGE 4
■ Pay attention to the dimensions of the cutting discs. The diameter of the centre hole must fit the flange without play. Do not use any reduction pieces or adapters. ■ Only use the machine for dry cutting in stone. ■ Mind hidden electric lines, gas and water pipes. Check your working area, e.g. with a metal detector. Measured sound value Measured values determined according to EN 50 144. Typically the A-weighted noise levels of the tool are: Sound pressure level = 86 dB (A). Sound power level = 99 dB (A).
PAGE 5
Brief description On/Off switch with locking device Spindle lock Direction of rotation arrow Infinitely variable cutting width adjustment 15-26 mm. Cutting width adjustment 6-14 mm with set of distance plates (special accessory). Infinitely variable cutting depth adjustment with movable supporting table. No-load speed limit for low-noise operation Electronic speed adjustment ensures constant speed even when the load on the motor varies.
PAGE 6
Switching on: Push the sliding switch forward. To lock, depress the front part of the switch. Switching on and off 1 2 Switching off: To unlock, depress the back part of the sliding switch. The switch will automatically move back to “O”. Dust extraction ENGLISH Only use the machine with a suitable dust-remover! Insert the suction hose connector into the adapter until it sits firmly. Connect the other end of the suction hose to a vacuum cleaner which is suited for dust extraction.
PAGE 7
Always disconnect the plug from the socket before carrying out any work on the machine. Exchanging the diamond cutting discs Spanntec-nut Round nut with drilled holes in one face Disassembly 1. Loosen the screws and remove the protective cover. 2. Lock the work spindle by depressing the spindle lock. Open the round nut of the upper cutting disc with aid of a pin-type face spanner and remove it. Remove the upper cutting disc. 3. Lock the work spindle by depressing the spindle lock.
PAGE 8
Loosen the Allen screw of the Spanntec-nut with the T-key (to stop). Setting the cutting width Move the outer diamond cutting disc to the required cutting width. Spanntec To lock it in the required position fasten the Allen screw tightly. Set of distance plates (special accessory) 1. Loosen the screw and open and remove the protective cover. 2. Lock the work spindle by depressing the spindle lock. Open the round nut of the upper cutting disc with aid of a pin-type face spanner and remove it.
PAGE 9
Only use the machine for dry cutting in stone. Advices for operation Mind hidden electric lines, gas and water pipes. Check your working area, e.g. with a metal detector. 1. Pre-select the cutting depth and width. 2. Switch the machine on. 3. Set the machine with the front edge of the cutting support touching the masonry and lower it gently in until the cutting support lies flush. 4.