Specifications

CHAPTER 5 In Case of Trouble Troubles for which error messages are displayed
5-18
∗∗∗∗∗ ERROR 20 ∗∗∗∗∗
I/F BOARD 01
An error occurred in the control sys-
tem.
Turn off the power to the printer and
turn it on after a while. If the same
error message appears again, contact
your local distributor to call for ser-
vice.
∗∗∗∗∗ ERROR 20 ∗∗∗∗∗
I/F BOARD 02
An error occurred in the control sys-
tem.
∗∗∗∗∗ ERROR 20 ∗∗∗∗∗
I/F BOARD 03
An error occurred in the control sys-
tem.
∗∗∗∗∗ ERROR 20 ∗∗∗∗∗
I/F BOARD 04
An error occurred in the control sys-
tem.
∗∗∗∗∗ ERROR 21 ∗∗∗∗∗
I/F NONE
An error occurred in the control sys-
tem.
Turn off the power to the printer and
turn it on after a while. If the same
error message appears again, contact
your local distributor to call for ser-
vice.
∗∗∗∗∗ ERROR 23 ∗∗∗∗∗
HOST I/F
Timeout error occurred during commu-
nication between the host computer
and the interface board for IEEE-1394
connection.
Check that the cable is securely con-
nected to the host computer and inter-
face board. Also, check to see if any
error has occurred on the host com-
puter.
∗∗∗∗∗ ERROR 24 ∗∗∗∗∗
I/F INITIAL
An error occurred in the control sys-
tem.
Turn off the power to the printer and
turn it on after a while. If the same
error message appears again, contact
your local distributor to call for ser-
vice.
∗∗∗∗∗ ERROR 25 ∗∗∗∗∗
FULL-SPEED
An error occurred in communication
between the host computer and the
interface board for USB2.0 connec-
tion.
(Full-Speed mode connection)
Check that the host PC supports the
USB2.0 interface.
(Communication can be resumed with-
out changing any setting. However, it
is recommend to use the connection in
High-Speed mode.)
∗∗∗∗∗ ERROR 25 ∗∗∗∗∗
PACKET SIZE OVER
An error occurred in communication
between the host computer and the
interface board for USB2.0 connec-
tion.
Check that the cable is securely con-
nected to the host computer and inter-
face board. Also, check to see if any
error has occurred on the host com-
puter.
∗∗∗∗∗ ERROR 25 ∗∗∗∗∗
USB PROTOCOL
An error occurred in communication
between the host computer and the
interface board for USB2.0 connec-
tion.
∗∗∗∗∗ ERROR 25 ∗∗∗∗∗
USB ENVIRONMENT
An error occurred in communication
between the host computer and the
interface board for USB2.0 connec-
tion.
∗∗∗∗∗ ERROR 25 ∗∗∗∗∗
USB DATA
An error occurred in communication
between the host computer and the
interface board for USB2.0 connec-
tion.
∗∗∗∗∗ ERROR 30 ∗∗∗∗∗
OPERATION ERROR
Improper operation was conducted on
the operation panel.
The Display 1 shows the cause of the
error.
Remove the cause, and perform a
proper operation.
∗∗∗∗∗ ERROR 34 ∗∗∗∗∗
DATA REMAIN
It is being tried to change settings for
functions though there remains
received data that has not yet been
printed.
Print all the received data or execute
the data clear function. Then, change
settings.
Error message Cause Remedy