Specifications

5-19
CHAPTER 5 In Case of Trouble Troubles for which error messages are displayed
∗∗∗∗∗ ERROR 40 ∗∗∗∗∗
MOTOR ALARM X
An error occurred in the control sys-
tem.
Turn off the power to the printer and
turn it on after a while. If the same
error message appears again, contact
your local distributor to call for ser-
vice.
∗∗∗∗∗ ERROR 41 ∗∗∗∗∗
MOTOR ALARM Y
An error occurred in the control sys-
tem.
∗∗∗∗∗ ERROR 42 ∗∗∗∗∗
X OVER CURRENT
An error occurred in the control sys-
tem.
∗∗∗∗∗ ERROR 43 ∗∗∗∗∗
Y OVER CURRENT
An error occurred in the control sys-
tem.
∗∗∗∗∗ ERROR 45 ∗∗∗∗∗
CAPPING : SENSOR
An error occurred in the control sys-
tem.
∗∗∗∗∗ ERROR 45 ∗∗∗∗∗
CAPPING : PARAMETER
An error occurred in the control sys-
tem.
∗∗∗∗∗ ERROR 46 ∗∗∗∗∗
WIPER
An error occurred in the control sys-
tem.
∗∗∗∗∗ ERROR 47 ∗∗∗∗∗
STATION
An error occurred in the control sys-
tem.
∗∗∗∗∗ ERROR 49 ∗∗∗∗∗
CUTTER SOLENOID
An error occurred in the control sys-
tem.
∗∗∗∗∗ ERROR 50 ∗∗∗∗∗
MEDIA DETECT
Paper could not be detected. The media
set position or media itself is not
proper.
If the same error message appears
again even after setting the media
properly, contact your local distributor
to call for service.
∗∗∗∗∗ ERROR 50 ∗∗∗∗∗
THICKNESS DETECT
Media thickness could not be detected. Input the media thickness or select the
END key and execute media detection
again.
∗∗∗∗∗ ERROR 51 ∗∗∗∗∗
Y-ORIGIN
Y-origin could not be detected. Turn off the power to the printer and
turn it on after a while. If the same
error message appears again, contact
your local distributor to call for ser-
vice.
∗∗∗∗∗ ERROR 53 ∗∗∗∗∗
HEAD HEIGHT ORIGIN
Head height origin could not be
detected.
∗∗∗∗∗ ERROR 54 ∗∗∗∗∗
MEDIA JAM
Paper jam was detected. Open the front cover and raise the
clamp lever, and remove the jammed
paper.
If the same error message appears
again even after clearing the paper jam
status, contact your local distributor to
call for service.
∗∗∗∗∗ ERROR 58 ∗∗∗∗∗
POSITION ENCODER:DIR
An error occurred in the control sys-
tem.
Turn off the power to the printer and
turn it on after a while. If the same
error message appears again, contact
your local distributor to call for ser-
vice.
∗∗∗∗∗ ERROR 58 ∗∗∗∗∗
POSITION ENCODER:CNT
An error occurred in the control sys-
tem.
∗∗∗∗∗ ERROR 59 ∗∗∗∗∗
CUTTER ENCODER
An error occurred in the control sys-
tem.
∗∗∗∗∗ ERROR 64 ∗∗∗∗∗
TAKE-UP VOLTAGE
An error occurred in the control sys-
tem.
∗∗∗∗∗ ERROR 64 ∗∗∗∗∗
FEEDER VOLTAGE
An error occurred in the control sys-
tem.
∗∗∗∗ ERROR 116 ∗∗∗∗
NCU I/F 00
An error occurred in the control sys-
tem.
Operation can be resumed after turning
off the nozzle missing detection func-
tion.
Turn off the power to the printer and
turn it on after a while.
If the error occurs frequently, contact
your local distributor to call for ser-
vice.
∗∗∗∗ ERROR 116 ∗∗∗∗
NCU I/F 01
An error occurred in the control sys-
tem.
Error message Cause Remedy