MIMAKI ENGINEERING CO., LTD. URL: http://eng.mimaki.co.
TABLE OF CONTENTS CAUTION ......................................................................... vi DISCLAIMER OF WARRANTY ........................................vi Requests ..........................................................................vi FCC Statement (USA) ......................................................vi Interference to televisions and radios...............................vi CDRH REGULATION......................................................vii Foreword .........................
Test drawing ......................................................... 2-10 Execution of head cleaning................................... 2-12 Drawing an image from source data ..................... 2-13 Starting the drawing operation................................. 2-13 Interruption of drawing............................................. 2-14 When [! WORK High] is displayed........................... 2-15 If you open the cover during drawing ...................... 2-15 Turning the power OFF..............
Setting mm/ inch ......................................................3-28 Setting weight of the empty cartridge.......................3-29 Setting Key buzzer ...................................................3-30 Setting radiator pump (only for UJF-3042HG) .........3-31 Setting the flushing level before printing ..................3-32 Set the vacuum function ........................................ 3-33 CHAPTER 4 Maintenance Routine maintenance...............................................
CHAPTER 5 In Case of Trouble Before taking a phenomenon as a trouble .............. 5-2 The machine cannot be energized ............................ 5-2 The machine cannot perform printing........................ 5-2 If image quality declines ............................................ 5-3 Resolving nozzle clogging ......................................... 5-3 Troubles for which error messages are given on the LCD .................................................... 5-4 Warning Message..................
CAUTION DISCLAIMER OF WARRANTY THIS LIMITED WARRANTY OF MIMAKI SHALL BE THE SOLE AND EXCLUSIVE WARRANTY AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS, AND MIMAKI NEITHER ASSUMES NOR AUTHORIZES DEALER TO ASSUME FOR IT ANY OTHER OBLIGATION OR LIABILITY OR MAKE ANY OTHER WARRANTY OR MAKE ANY OTHER WARRANTY IN CONNECTION WITH ANY PRODUCT WITHOUT MIMAKI’S PRIOR WRITTEN CONSENT.
CAUTION CDRH REGULATION The Center for Devices and Radiological Health for the U.S. Food and Drug Administration Implement regulations for laser products. The sentence of “This product complies with 21 CFR chapter I and subchapter J” indicates compliance with the CDRH regulations and is labeled on the product when marketed in the United States. This Model is equivalent to Class II laser device according to CDRH Regulation.
Foreword Congratulations on your purchase of a MIMAKI "UJF-3042HG/6042" model of UV ink jet printer. UV Inkjet Printer UJF-3042HG/6042 uses ultraviolet ray curing ink (UV ink). Read this Operation Manual carefully and make the most effective use of your printer. On this operation manual • This Operation Manual describes the operation and maintenance of Model UJF-3042HG/6042 Color Ink Jet Printer (hereinafter referred to as the machine).
For safe operation Symbols Symbols are used in this Operation Manual for safe operation and for prevention of damage to the machine. The indicated sign is different depending on the content of caution. Symbols and their meanings are given below. Please follow these instructions as you read this manual. Examples of symbols Failure to observe the instructions given with this symbol can result in death or serious injuries to personnel. Be sure to read it carefully and use it properly.
WARNING • Be sure to setup the appropriate air-moving system in case of using this machine in a closed room or a room with bad ventilation. Cautions for constructing exhaust outlet Please observe the following cautions to avoid breakdown of this machine. (1) The opening area of the exhaust outlet requires more than half of the duct entrance area. (2) If mounting a valve on the exhaust outlet, be sure to open the valve when using the machine.
For safe operation Never do the following WARNING Do not disassemble or remodel the machine • Never disassemble or remodel this machine and the ink cartridge. Disassembling or remodeling any of them will result in electric shocks or breakdown of this machine. Do not use this machine in damp places • Avoid damp environment to use this machine. Do not splash water onto this machine. High humidity or water will give rise to fire, electric shocks or breakdown of this machine.
WARNING Wearing protective devices • When cleaning the suction nozzle, which may scatter ink, be sure to wear safety glasses and gloves, or ink and cleaning solution might enter your eyes or ink and cleaning solution put on your hands might make your hands rough. Power supply and voltage • Use this machine with indicated power specifications. Be sure to connect the power cable plug to the grounded outlet, or it may cause fire or electric shock.
For safe operation Precautions for use CAUTION Protection against dust • It is strongly recommended to use the machine in a room that is not dusty. Set the Refresh level 2 or 3 when in bad environment. • When leaving the work place after the working hours, be sure to remove media from the printer.If any media is left on the printer, dust can put on it. • Store media not to put dust on it. Wiping dust off the media, dust will be put on the media due to static electricity.
CAUTION Notes on LED UV • When handling the glass on the bottom of the LED UV unit, be sure to wear the gloves attached and never touch them with bare hands. Or the UV ink curing level may significantly lower. If the glass becomes dirty, wipe it with clean gauze moistened with alcohol. (Do not use alcohol for cleaning the exterior cover, or the paint will peel off.) • The LED UV performance and service life are significantly affected by the UV irradiation and UV power supply units used.
For safe operation Precautions for installation CAUTION A place exposed to direct sunlight A place that is not horizontal A place where temperature and humidity varies significantly •Use the machine under the following environment. Operating environment : 20 ～ 35 ℃ (68 to 95 °F) 35 ～ 65% (Rh) A place that vibrates A place exposed to direct air blow from air conditioner, etc.
Position of the warning label Warning labels are adhered on this machine. Be sure to fully understand the warnings given on the labels. In the case where any of the warning label has become so soiled that the warning message is illegible or has come off, purchase a new one from your local distributor or our office.
Position of the warning label Order No. Label Order No.
Position of the warning label Vacuum table Warning labels are adhered on vacuum table. Order No. Label Order No.
How to Read This Operation Manual This manual provides the explanation about the displayed characters and used keys on the “Display Panel” in addition to the operation procedures. Proceed operations confirming them while using. These are what we want you to know in advance. This explains the outline of functions. These are the number of operation procedures. This shows the display panel. Page number enclose shows the buttons in a sentence.
xx
CHAPTER 1 Before Use This chapter describes the parts name and setting procedures before use. Installing the machine ......................................................... 1-2 Where to install the machine .......................................................1-2 Moving this machine ...................................................................1-3 Configuration and Function................................................ 1-4 Front ..................................................................
Installing the machine Where to install the machine Secure sufficient space for installation before assembling this machine. Decide the place considering the size of the machine and a space required for drawing. Model Width Depth Height Total Weight UJF-3042HG 1200 mm 1090 mm 920mm Approx.130 kg UJF-6042 1510 mm 1090 mm 960mm Approx.
Installing the machine Moving this machine Move this machine as follows when this machine is required to move on the step-free same floor. • When moving this machine, take care not to give a significant impact on it. • If you tilt this machine, movable part(Y bar) may move. Move this after pulling the Y bar to either front or back side or avoiding tilt • When moving this machine, keep it as flatly as possible. Do not move it on its side. It may cause machine failure.
Configuration and Function Front Ink station Insert ink cartridges here.( Table ( Carriage ( P.2-4) Set media on it. P.1-12) P.1-6) Y-bar Moves on the table at drawing. Power button Turn ON/OFF the power of this machine instead of the power switch of main body. ( P.2-3, P.2-16) Operation Panel ( P.1-5) Operation keys for setting the machine, and a display to display operation items are placed. Rear Unusable (used for maintenance) USB socket Connect USB interface cable.
Configuration and Function Operation Panel The operation panel is used for setting of drawing method and each operation. POWER Lamp Lights when the power is ON. VACUUM TEST Press to switch ON/OFF of the vacuum. Key Press to start the test drawing. ( P.2-10) Display Displays state of the machine, setting items, errors, and so on. CLEANING 1 Key Press to start the head cleaning. ( P.2-12) DATACLEAR Key JOG key Used for moving of the Y-bar and for each setting.
Configuration and Function Carriage A print head for drawing, LED UV device, and a light pointer in the print head cover are mounted on the carriage. EMERGENCY SWITCH When stopping the machine for safety reason, press the switch. One EMERGENCY switch is placed on the front face of the machine.
About vacuum table It is necessary to adjust the table height depending on the media thickness because various media can be set for drawing. This machine provides you with two jigs for adjusting the table height (vacuum tables).
About tap position The table and the vacuum table on which the media set have the M4 tap (UJF-3042HG: for 12 positions, UJF6042: for 16 positions) of the size below respectively. You can download data illustrating the tap positions from the "Manual" section of the Mimaki Engineering download page (http://eng.mimaki.co.jp/download/). • UJF-3042HG 100 100 12-M4 200 Vacuum Table 15 15 35 35 100 100 200 Table 176.8 150 26.8 1-8 Origin 176.8 150 26.
About vacuum table • UJF-6042 100 24-M4 200 1 15 35 Before Use 100 Table 176.8 155 155 150 26.8 200 100 24-M4 15 35 100 Vacuum Table 176.8 155 155 150 Origin 26.8 • Although tap holes ( ) are open except the tap position in the drawing ( ), they are necessary in the production process. Therefore, please do not use them. • We may change the position except specified tap holes ( ) without prior notice.
About vacuum table Notes on vacuum table When you use the jig (vacuum table), the size shall be smaller than UJF-3042HG: 420 / UJF-6042: 720 millimeters wide and 505 millimeters long. If you make the size be more than above, the table cannot move.
Connecting the cables Connecting the USB2.0 interface cable Connect a computer to this machine with the USB2.0 interface cable. • Prepare the USB2.0 interface cable. (USB2.0 interface cable is not supplied with this machine.) • Your RIP is required to support USB2.0 interface. • If USB2.0 interface is not installed in your computer, ask a RIP maker near you or our branch office. 1 Before Use Connecting the power cable • Use only the supplied power cable.
Setting of ink cartridge Use the ink cartridge inserting it into the ink station. Kinds of ink that can be used Ink Type Color Magenta Cyan Yellow Black Light magenta UV Ink Light cyan White Clear Primer Cleaning cartridge *1 *1. To be used when the head is cleaned.
Setting of ink cartridge Precautions in handling ink cartridge 1-13 1 Before Use • Use the recommended ink cartridge by Mimaki. • Do not touch the ink directly. If the ink settles on the skin or clothes, immediately wash it off with soap and water. If you get ink in your eyes, immediately wash your eyes with a lot of clean water. Then, consult a doctor as soon as possible. • Store ink cartridge in a dark and cold place.
About Media The sizes of media that can be used and the method of handling are described here. The sizes of media that can be used Maximum width UJF-3042HG: 300 mm UJF-6042: 610mm Maximum length 420 mm Max. drawing width UJF-3042HG: 300 mm UJF-6042: 610mm Max. drawing length 420 mm Thickness Between 100mm and 150mm Weight *1 UJF-3042HG: Less than 5 kg UJF-6042: Less than 7 kg *1. A rough guide is 50 kg per 1 m2.
Menu mode This machine has three modes. Each mode is described below. Local Mode Local mode is a mode in drawing preparation state. All keys are available. Receiving of data from the computer is allowed, however, drawing is not executed. The following operations are allowed in the local mode. (1) Setting an origin and the table height by pressing the JOG keys. (2) Executing “Test drawing” by pressing the TEST key. (3) Executing “head cleaning” by pressing the CLEANING key.
1-16
CHAPTER 2 Basic Operations The procedure from preparation of ink and media to the execution of drawing, and setting methods are explained. Operation flow...................................................................... 2-2 Turning the power ON ......................................................... 2-3 Setting the media ................................................................. 2-4 Set the media in another method ................................................2-9 Test drawing..............
Operation flow 1 2 3 4 5 6 2-2 Turning the power ON See "Turning the power ON" ( Setting the media See "Setting the media" ( Test drawing See "Test drawing" ( Execution of head cleaning See "Execution of head cleaning" ( P.2-12) Drawing an image from source data See "Drawing an image from source data" ( P.2-13) Turning the power OFF See "Turning the power OFF" ( P.2-3) P.2-4) P.2-10) P.
Turning the power ON • When the power is turned ON, the Y-bar moves. To avoid injuries, keep your hands away from the table. 1 Press the power button. • Press the power button on the left side of the operation panel to light. • When the main power switch is not set to ON, the power is not connected even if the power button is pressed. If the lamp does not light even if the button is pressed, check the main power switch on the rear of this machine.
Setting the media • When the media thickness is 100mm and less, media inflation is required so that the media thickness may be 100mm. • When the media thickness is 100mm and more, it is necessary to align it with the drawing height with the table up/ down key. • The peripheral parts of the media could roll up due to heat. Fix the media supplementarily using adhesive tapes, etc. 1 Open the table front cover. 2 Set media along the L-shaped mark (drawing origin) on the right corner of the table.
Setting the media Change the height of the vacuum table (UJF-3042HG) Depending on the media thickness, change the height of the vacuum table (50mm or 100mm). You can change the height of the vacuum table by replacing four table spacers that support the table (for 50mm or 100mm). The default setting of the vacuum table height is “for 100mm”. This chapter explains the procedures to change the table height to “50mm”. 1 Press the JOG key rear edge. 2 Press the TABLE lowest position.
7 Attach the table spacer 50. 8 Attach the assembled vacuum table on the main body. • Attach the table spacer 50, and fix it with a 10mm spanner. (1) Attach the vacuum table on the original position, and insert the connector for the vacuum fan. (2) Turn on the power supply.
Setting the media Change the height of the vacuum table (UJF-6042) Depending on the media thickness, change the height of the vacuum table (50mm or 100mm). You can change the height of the vacuum table by attaching and removing four table spacers that support the table (for 50mm or 100mm). The default setting of the vacuum table height is “for 100mm”. This chapter explains the procedures to change the table height to “50mm”. 1 Perform steps 1 to 5 on P.
• When you change the table spacer, the height of the vacuum table changes as below: When using table spacer 100 100mm When using table spacer 50 50mm • The height of vacuum table is changed as shown below if the table spacers are removed. • Attach the spacer by rotating by hand without any tool such as a spanner.
Setting the media Set the media in another method You can move the Y bar to the rear so that you may set the media easier. 1 Press the FUNCTION key in the local mode. 2 Press the 3 To check the height, press the FUNCTION key. 4 Press the ENTER key. • The table is lowered. • When the media thickness is 100mm and less, it is necessary to attach the vacuum table so that the media thickness may be 100mm.
Test drawing Make test drawing in the specified direction to check whether there is nozzle clogging or other drawing failures (such as wearing or missing). As the distance between head tables is 100mm, use the attached vacuum table. Check before starting test drawing • Is media set? ( P.2-4) 1 Press the 2 Select the drawing direction by pressing the key, and press the ENTER key. TEST • Is origin point set? ( key in the local mode. P.
Test drawing Normal pattern Nozzle drop out Many lines are missing. Abnormal patterns Nozzle missing The lines are missing as if the teeth are lost. Deflection The distance between the lines is narrowing or double lines are formed.
Execution of head cleaning When a correct pattern is not obtained in the test drawing, perform the head-cleaning. As for the head cleaning, the following 4 types are available. normal To be used if ten odd numbers of the lines are missing when the test pattern is made. Suction and wiping will be performed. hard To be used when the missing of the lines does not improve with the “normal” cleaning. soft To be used when the lines are curved.
Drawing an image from source data Starting the drawing operation • If the temperature of the head has not reached the predetermined value, a message is displayed. Drawing is not allowed in such cases. When the display is disappeared, drawing can be started. • Data transmission is allowed even if errors are displayed. Drawing is started after the display is disappeared. 1 Set the media. ( 2 Press the REMOTE key in the local mode. 3 Transmit data to be drawn from the computer. P.
4 Start drawing. 5 Taking out the media after completion of drawing. • The drawing origin is not changed after completion of the drawing. (1) When you made vacuum ON, Press the VACUUM key to turn the adsorption OFF. • When you use the vacuum function of the vacuum table to draw, turn OFF the vacuum when drawing has been completed. (P.3-33 “Set the vacuum function”) (2) Remove the media. • During printing, media may be heated by the LED UV and raised, causing drawing to be interrupted.
Drawing an image from source data When [! WORK High] is displayed When [! WORK High] is displayed on the screen and the drawing operation stops during drawing, restart drawing with the procedures below: E RROR ! WO R K H i g h 505 • During drawing, the sensor always monitors the media height. When the gap check function ( P.3-8) is set to “OFF”, if the sensor detects the media, the drawing operation is interrupted automatically, and [! WORK High] is displayed on the screen.
Turning the power OFF To turn off, check first whether or not there is data received and there remains data that has not yet been output in the machine. 1 Turn the power of the connected computer off. 2 Press the power button to cut the power. When this machine is not used for a long time, execute the following: (1) Press the power button. (2) Confirm that the shutdown operation is completed. (3) Turn off the main power switch on the rear of this machine. ( P.
CHAPTER 3 Useful Function Items required for using this machine conveniently, such as an ink replacing method or a cleaning manner, are described. Changing origin .................................... 3-2 Changing origin with JOG keys ................ 3-2 Changing origin with FUNCTION menu ... 3-3 Setting the Head Height ....................... 3-4 Setting the table spacer ............................ 3-4 Setting the media thickness ..................... 3-5 Setting the head gap ..........................
Changing origin The default origin position can be changed. There are following 2 changing methods. Changing with the JOG keys Changing with the “ORIGIN” in the FUNCTION menu Changing origin with JOG keys 1 Press the in the local mode. 2 Move the light pointer mark by pressing the keys. keys SET UP －－－ OR I G I N 420 . 0 SET UP 300 . 0 • The origin setting mode starts • A red light pointer mark [ ] is projected on the table or the media.
Changing origin Changing origin with FUNCTION menu To precisely set the origin of coordinates, set its X- and Y- coordinates from the FUNCTION menu. This setting value becomes the origin position (0, 0). 1 Press the FUNCTION key in the local mode. 2 Select the [ORIGIN] by pressing the and press the ENTER key twice. 3 Input value by pressing the or keys, and press the < L OC A L > or key, F UNC T I ON S E T OR I G I N < ENT > • X-axis offset value setting screen is displayed.
Setting the Head Height For the head height setting, you can set the items below: • Height of vacuum table and table spacer • Media thickness • Head gap • Table height • Gap check Setting the table spacer When you use the vacuum table and the table spacer depending on the media thickness, set the height of “vacuum table + table spacer”. (Supported from the firmware ver.3.00) 1 Press the FUNCTION key in the local mode. 2 Select the [HEAD HEIGHT] by pressing the key, and press the ENTER key.
Setting the Head Height Setting the media thickness If the media thickness is changed, Table Height is also changed. 1 Press the FUNCTION key in the local mode. 2 Select the [HEAD HEIGHT] by pressing the key, and press the ENTER key. 3 Select the [MEDIA THICKNESS] by pressing the keys, and press the ENTER key. 4 Set the media thickness by pressing the keys, and press the ENTER key.
Setting the head gap If the head gap is changed, Table Height is also changed. 1 Press the FUNCTION key in the local mode. 2 Select the [HEAD HEIGHT] by pressing the key, and press the ENTER key. 3 Select the [HEAD GAP] by pressing the keys, and press the ENTER key. 4 Set the head gap by pressing the and press the ENTER key. < L OC A L > or or or keys, • Set value: 1.5mm to 5.0mm 5 3-6 Press the END key several times to end the setting.
Setting the Head Height Setting the table height If the table height is changed, Media Thickness is also changed. 1 Press the FUNCTION key in the local mode. 2 Select the [HEAD HEIGHT] by pressing the key, and press the ENTER key. 3 Select the [TABLE HEIGHT] by pressing the keys, and press the ENTER key. 4 Set the table height by pressing the and press the ENTER key.
Setting the Head Height Gap check Select operation when obstacles are detected during drawing. 1 Press the FUNCTION key in the local mode. 2 Select the [HEAD HEIGHT] by pressing the key, and press the ENTER key. 3 Select the [GAP CHECK] by pressing the keys, and press the ENTER key. or 4 Select the mode by pressing the press the ENTER key.
Other useful functions Data clear Erase the data not required for this machine with the following operation. 1 Press the DATACLEAR 2 Press the ENTER key in the local mode. key. < L OC A L > DATA CL EAR < ENT > • The data is erased. Displaying information of this machine 1 The information is displayed sequentially by pressing the ENTER key in the local mode. • The following information are displayed.
Proceed with drawing that you suspended When you open the cover during printing data, drawing is suspended. In such a case, you can proceed with it continuously by performing the procedures below. • When you suspended test drawing, you cannot continue it. • When you proceed with drawing that you suspended, the image quality and the precision may not be guaranteed. • When you suspended drawing because an error had occurred, you cannot proceed with it.
Other useful functions Alternative nozzles for printing, when nozzles missing can not be improved NOZZLE RECOVERY: When nozzles missing can not be improved at specific points, other good nozzles can be used as alternatives for printing. 1 Press the FUNCTION key in the local mode. 2 Select the [MAINTENANCE] by pressing the key, and press the ENTER key. 3 Select the [NOZZLE RECOVERY] by pressing the key, and press the ENTER key.
6 Register the Nozzle number that needs NOZZLE RECOVERY and then press ENTER key. • • NOZ Z L E R E COV E R Y H1 -M NG 3 : 1 4 6 : Keys for selecting the registration number from 1 to 5. : Keys for registering the nozzle number that needs recovery from 1 to 192 or selecting “OFF”; no nozzle registration. Recovery nozzle No.: OFF, 1 to 192 Registration number: 1 to 5 Example of nozzle to be recovered Nozzle missing No.102 Nozzle number Registration Recovery number Nozzle No. Nozzle missing 1 12 No.
Other useful functions Checking ink landing displacement You can check for ink landing displacement from causes such as the equipment table shaking. (UJF-3042HG: Supported from the firmware ver.3.80, UJF-6042: Supported from the firmware ver.1.30) 1 Press the FUNCTION key in the local mode. 2 Select the [MAINTENANCE] by pressing the key, and press the ENTER key. 3 Select the [DISPLACEMENT] by pressing the key, and press the ENTER key.
Various settings Setting the print method Set items for printing. 1 Press the FUNCTION key in the local mode. 2 Select the [SET UP] by pressing the and press the ENTER key. 3 Select the [PRINT MODE] by pressing the key, and press the ENTER key. 4 Press the 5 Select an item to be set by pressing the key, and press the ENTER key. ENTER < L OC A L > or key, F UNC T I ON WO R K S E T < ENT > SET UP P R I N T MO D E SET UP QUA L I T Y or key.
Various settings Setting the mode of the LED UV The mode of the LED UV may be set in 3 stages. This setting is made when the media vulnerable to the heat is used or when the test drawing is made in which the lighting of the LED UV is not desired. ON The LED UV is lit. OFF The LED UV is not lit. NOPRINT The drawing is not performed and only the LED UV is lit. Use when drawing is performed without the LED UV is lit etc., and when you wish to make it cure afterward.
Increasing cumulative UV irradiation when the number of passes is low When the number of passes is low (720x600: 8 passes or less, 720x900: 12 passes or less, 720x1200: 8 passes or less), cumulative UV light quantity irradiated to the discharged ink is smaller, which may cause insufficient UV curing for some media type. Setting [UV Curing Level] reduces the number of nozzles to be used when the number of passes is low. Increasing the scan count increases the cumulative UV light quantity.
Various settings Setting of priority Select priority of setting of this machine or that of the computer on the following items respectively. Items to be selected : Print mode / Feed compensation / Ink layers / Logical seek / Refresh 1 Press the FUNCTION key in the local mode. 2 Press the [SET UP] by pressing the and press the ENTER key. 3 Select the [PRIORITY] by pressing the and press the ENTER key. 4 Select the set value by pressing the and press the ENTER key.
Setting of fan mode When you use the vacuum table, you can set whether the vacuum function to fix the media set on the vacuum table is performed automatically or you perform it manually. The factory default is “AUTOMATIC”. (Supported from the firmware ver.3.00) 1 Press the FUNCTION key in the local mode. 2 Press the [SET UP] by pressing the and press the ENTER key. 3 Select the [FAN MODE] by pressing the key, and press the ENTER key.
Various settings Setting the work change Set whether to return to the local mode or keep the remote mode after online drawing. 1 Press the FUNCTION key in the local mode. 2 Press the [SET UP] by pressing the and press the ENTER key. 3 Select the [WORK CHANGE] by pressing the key, and press the ENTER key. 4 Select “OFF” or “ON” by pressing the and press the ENTER key.
Setting the ink weight If weight of the cartridge is not entered when filling ink, enter the weight when INK LVL LOW or INK LVL END is detected. This machine recalculates remaining amount of ink and writes the value into the IC chip. (600ml ink only) 1 Press the FUNCTION key in the local mode. 2 Press the [SET UP] by pressing the and press the ENTER key. 3 Select the [CART WEIGHT] by pressing the key, and press the ENTER key. 4 Select cartridges by pressing the < L OC A L > or or key, or key.
Various settings Changing language display on the screen Display language can be selected between Japanese and English. 1 Press the FUNCTION key in the local mode. 2 Select the [DISPLAY] by pressing the and press the ENTER key. 3 Select a language by pressing the press the ENTER key. or or < L OC A L > key, key, and F UNC T I ON D I SPLAY < ENT > D I SPLAY Eng l i sh • Default is “English.” 4 Press the END key to finish. • Set value remains even after turning off the power.
Output the setting list Keep the list for customer’s record or send it by the fax at inquiry on the maintenance. 1 Set a larger media than the legal size. ( 2 Press the FUNCTION key in the local mode. 3 Select the [MAINTENANCE] by pressing the key, and press the ENTER key. 4 Select the [LIST] by pressing the press the ENTER key. • Output of the setting list starts. 5 3-22 Press the END key to finish. P.
Various settings Displaying machine information 1 Press the FUNCTION key in the local mode. 2 Select the [MAINTENANCE] by pressing the key, and press the ENTER key. 3 Select the [INFORMATION] by pressing the key, and press the ENTER key. 4 Select information to be displayed by pressing the or key, and press the ENTER key. < L OC A L > or or • The following 4 information can be displayed. FW version of this machine Serial No. Head serial No. Error history • For Head serial No.
About Displayed Information This section describes how to read displayed information. ERROR HISTORY Displaying the occurrence date [ 00000 ] 2014 / 01 / 23 12 : 34 : 56 E RROR I NK END 602 The error occurrence date and error message are displayed alternately. [ 00001 ] 2014 / 01 / 23 01 : 23 : 45 key: Displays an error that occurred more recently. key: Displays an error that occurred further in the past. • The smaller the number at the top left, the more recently the error occurred.
Various settings Other useful settings Change settings according to need. 1 Press the FUNCTION key in the local mode. 2 Select the [SET UP] by pressing the and press the ENTER key. 3 Select an item to be set by pressing the key, and press the ENTER key. < L OC A L > or key, or F UNC T I ON WO R K S E T < ENT > SET I NK UP L AYERS • Select with reference to the Table of Setting below. 4 Select a value to be set by pressing the and press the ENTER key.
Initializing settings 1 Press the FUNCTION key in the local mode. 2 Select the [SET UP] by pressing the and press the ENTER key. 3 Select the [SETUP RESET] by pressing the key, and press the ENTER key. 4 Press the 5 Press the ENTER < L OC A L > or key, or key. • Resets the setup. END F UNC T I ON WO R K S E T < ENT > SET UP SETUP RESET SET UP I N I T I AL . key several times to end the setting.
Various settings Setting time 1 Press the FUNCTION key in the local mode. 2 Select the [MACHINE SET] by pressing the key, and press the ENTER key. 3 Press the 4 Set time by pressing the ENTER < L OC A L > or key twice. • Selecting date (year/month/date/hour/minute): use • Entering date (year/month/date/hour/minute): use key. . F UNC T I ON MA CH I N E S E T < ENT > MA CH I N E S E T S E T T I ME S E T T I ME DATE= 2 0 1 2 . 0 2 . 0 5 .
Setting mm/ inch Set the unit to be used on this machine. 1 Press the FUNCTION key in the local mode. 2 Select the [MACHINE SET] by pressing the key, and press the ENTER key. 3 Select the [MM/INCH] by pressing the and press the ENTER key. 4 Select the unit by pressing the press the ENTER key. • Setting of the unit : use 5 3-28 Press the END or < L OC A L > or or key, key, and . key several times to end the setting.
Various settings Setting weight of the empty cartridge Enter weight of the empty cartridge. It is used for recalculating remaining amount of ink. (600ml ink only) 1 Press the FUNCTION key in the local mode. 2 Press the [MACHINE SET] by pressing the key, and press the ENTER key. 3 Select the [600ml CARTRIDGE] by pressing the key, and press the ENTER key. 4 Select cartridges by pressing the 5 Enter weight of the cartridge by pressing the key, and press the ENTER key.
Setting Key buzzer Set the buzzer sound when keys are pressed. 1 Press the FUNCTION key in the local mode. 2 Select the [MACHINE SET] by pressing the key, and press the ENTER key. or 3 Select the [KEY BUZZER] by pressing the key, and press the ENTER key. or 4 Select ON/OFF by pressing the press the ENTER key.
Various settings Setting radiator pump (only for UJF-3042HG) On UJF-3042 and UJF-3042FX, if the noise of the cooling pump for LED UV unit become louder after updating the firmware to the version 3.10 or later, change the setting as follows. This setting change is applicable on the firmware version 3.10 and later. On UJF-3042HG, this noise problem does not occur. (Supported from the firmware ver.3.10) 1 Press the FUNCTION key in the local mode.
Various settings Setting the flushing level before printing When using a clear acrylic jig and so on, the ink may splash on the print result as the ink on the nozzles thickens due to stray light. If this happens, increase the flushing amount before printing to prevent ink from splashing. (Supported from the firmware ver.4.00) 1 Press the FUNCTION key in the local mode. 2 Press the [SET UP] by pressing the and press the ENTER key.
Set the vacuum function Set ON/ OFF of the vacuum fan to be used for the vacuum table. (Only for UJF-3042HG. This function is not available for UJF-6042.) 1 Press the FUNCTION key in the local mode. 2 Select the [VACUUM] by pressing the 3 Press the 4 Select ON/OFF by pressing the 5 Press the ENTER 6 Press the END ENTER < L OC A L > or key key. < L OC A L > V A C U UM < ENT > V A C U UM V A C U UM : O F F or key, V A C U UM V A C U UM : ON key. key several times to end the setting.
3-34
CHAPTER 4 Maintenance Items required for using this machine conveniently, such as an ink replacing method or a cleaning manner, are described. Routine maintenance ........................... 4-2 When the waste ink is full.................. 4-14 When this machine is left unused for a long time ........................................................... 4-2 Precautions in cleaning ............................ 4-2 Cleaning exterior surfaces ........................ 4-3 Cleaning the table ....................
Routine maintenance Be sure to conduct maintenance works for the machine depending on operation frequency or periodically so as to use the machine for a long time while keeping its drawing accuracy. When this machine is left unused for a long time • Be sure to turn off the main power switch on the side of this machine. ( • Remove the media being set. P.1-4) Precautions in cleaning • Never disassemble this machine. Disassembling this machine can result in electric shock hazards or damage to this machine.
Routine maintenance Cleaning exterior surfaces If exterior surfaces of the machine is dirty, dampen a soft cloth with water or a neutral detergent diluted with water, squeeze it and wipe the surfaces. Cleaning the table The table is easy to become dirt with lint, paper dust or the like after cutting media. For a conspicuous stain, wipe it off with a soft-hair brush, a dry cloth, a paper towel or the like.
Ink cartridge Replacing with a new ink cartridge Replacing of ink cartridges is required in the following cases. Display Outline The ink in the ink cartridge is low. < L OC A L > I NK NEND • Drawing can be continued, but the ink may end during the drawing. Early replacement is recommended. • The display shown in the left indicates that magenta ink is low. M_ _ _ _ _ _ _ The ink in the ink cartridge ended. < L OC A L > I NK END • Unable to continue drawing. Replace with a new one immediately.
Ink cartridge Setting the ink set Set the ink set when ink type is changed. Contact a distributor in your district or our office to call for service. When you replace another kind of ink, wash all heads. When you replace with the same ink, it is necessary to wash and/ or fill of the No.3 head and/ or No.4 head. 1 Press the FUNCTION key in the local mode. 2 Select the [MAINTENANCE] by pressing the key, and press the ENTER key. 3 Select the [INK SET] by pressing the and press the ENTER key.
8 Remove the washing liquid cartridge. WA S H _ _ _ _ CL CL _ _ R E MO V E C A R T R I D G E WA S H I N G P L E A S E WA I T 9 Set the washing liquid cartridge to the ink station again. WA S H S E T WA S H I N G _ _ _ _ CL CL _ _ L I QU I D WA S H I N G P L E A S E WA I T 10 Remove the washing liquid cartridge.
Ink cartridge 14 Remove air from the ink port of the filled cartridge. • Remove air with syringe until ink comes out of the ink port. When all air is removed, press the ENTER key.
Ink cartridge Ink cartridge trouble When an ink cartridge trouble is detected, a warning message appears and printing, cleaning and all other activities that use ink are deactivated. In this case, replace the ink cartridge in question immediately. • Do not leave the ink cartridge without replacing for a long time as this will cause the nozzle clogging and the printer must be repaired by a service person. 1 Display the truble messages on the LCD. 2 Press the ENTER key. 3 Press the ENTER key again.
600ml Ink cartridge To use the 600ml ink cartridges, register the case weight (this page) and the cartridge weight (next page). Please prepare your scale (which can weigh up to 1200g in 1g). Registering the case weight Firstly register the case weight in the following procedures. For the 600ml cartridges, this machine recalculates remaining amount of ink from a registered case weight. 1 Weigh the case of an empty cartridge on the scale. 2 Prepare the 600ml cartridge.
Registering the cartridge weight After filling ink into the 600ml cartridge, register the cartridge weight. 1 After filling ink, press the 2 Press the 3 Remove the target cartridge, and weigh it on the scale. 4 Set the 600ml cartridge, enter the weight by pressing the or key, and press the ENTER key. 5 Press the END key several times. key. • An entry screen of the weight is displayed. ENTER key again. • If other 600ml cartridges are found, the entry screen is displayed.
600ml Ink cartridge Registering the cartridge weight (After LVL LOW / LVL END) The 600ml cartridge becomes level low when ink remains 60ml or less, and level end when ink remains 25ml or less. In this case, register the cartridge weight on the entry screen that is displayed. The level low or level end cartridge cannot be used until the weight is entered. 1 When a screen shown on the right appears, press the key. 2 Remove the target cartridge, and weigh it on the scale.
Avoiding dripping of ink droplet at printing Ink droplets from the mist at drawing may arise on the bottom of the carriage. As the ink droplets may drip and stain the media or cause blur or dot missing, clean the bottom of the carriage periodically. Tools • UJ Cleaning swab (SPC-0386) • Gloves 1 Turn the power on. 2 Press the FUNCTION key in the local mode. 3 Select the [MAINTENANCE] by pressing the key, and press the ENTER key. 4 Select the [STATION] by pressing the and press the ENTER key.
Avoiding dripping of ink droplet at printing 7 Dip the cleaning swab into the cleaning solution, and clean the side surface of the head. Light pointer • Do not wipe the nozzle face of the head. It may cause nozzle clogging. • To buy special cleaning swabs, contact a distributor in your district or our office. Bottom of the carriage • Be careful not to put the cleaning solution on the light pointer. 8 Dip the TechnoWipe (attached) into alcohol, and clean the LED-UV irratiation outlet.
When the waste ink is full Waste ink used for head cleaning gathers in the waste ink tank and the wiper bottle. Periodically check the waste ink tank and the wiper bottle and when they are full, dispose of the ink. If warning message such as “!WS INKTANK CHK” or “WIPER BOTTLE” appears, check the waste ink tank and the wiper bottle in the same way. • If you need a spare waste ink tank, contact a distributor in your district or our office. • Prepare a polyethylene tank to put in the waste ink.
When the waste ink is full 6 Open the waste ink box cover. 7 Remove the waste ink tank. 8 Put the waste ink into a tank with a cover. 9 Set the empty waste ink tank, and close the cover. • By pressing the cover lightly, the cover opens to the front. • Lifting the tank slightly up, pull it to the front. • Before putting the ink into the tank, put paper on the floor. (Not to stain the floor with ink) • Dispose of the waste ink pursuant to the regulations of your district.
Disposing of the waste ink in the wiper bottle 1 Turn the power on. 2 Press the FUNCTION key in the local mode. 3 Select the [MAINTENANCE] by pressing the key, and press the ENTER key. 4 Select the [STATION] by pressing the and press the ENTER key. 5 Select the [MENT:WIPER BOTTLE] by pressing the or key, and press the ENTER key. 6 Open the waste ink box cover. 7 Take the wiper bottle out, and dispose of the waste ink. • After initializing, is displayed.
When the waste ink is full 9 Press the 10 Press the ENTER END key. S T A T I ON C OM P L E T E D : en t key to finish.
Replacing the Filter To use this machine for a long time, clean the filter periodically (about once a week). • Put on supplied goggles and gloves. Ink may splash into the eye. • When a screw is dropped in replacing of the filter, contact a distributor in your district or our office. • LED UV unit filter (SPC-0657) • Mist adsorption filter (SPC-0656) • Gloves • Goggles Tools • Paper towel 1 Press the FUNCTION key in the local mode.
Replacing the Filter 6 Remove the filter retainer (2 places). 7 Replace the filters (2 places). 8 Attach the covers. 9 Press the (2) (1) (1) Turn and pull the right white knob. (2) Turn the left white knob and pull the frame of the filter. • Replace two filters. • Attach in reverse order of step 5, 6. ENTER • Initializing starts. key.
Washing the Nozzle To prevent nozzle clogging, execute nozzle washing at the end of the daily work. • Put on supplied goggles and gloves. Tools • UJ Cleaning swab (SPC-0386) • Gloves • Goggles • F-200 / LF-200 Washing Liquid (SPC-0568) 1 Press the FUNCTION key in the local mode. 2 Select the [MAINTENANCE] by pressing the key, and press the ENTER key. 3 Select the [STATION] by pressing the and press the ENTER key. 4 Select the [MENT:NOZZLE WASH] by pressing the or key, and press the ENTER key.
Washing the Nozzle 7 Dip washing liquid into the cleaning swab, and wipe dirt of the wiper nozzle. • Wipe the places shown in the right. 8 Back Front Put washing liquid into the dropper, and drop on the caps to fill them. • Fill the washing liquid into the four caps. 9 10 Replace the front cover, and press the ENTER key. • Capping is performed. Set leaving time by pressing the press the ENTER key. • Usually set 10 min. (Set value: 1 to 99 min) • After the leaving time, cleaning is performed.
Wash the ink discharge passage Wash the ink discharge passage regularly to prevent the head nozzles from clogging due to ink coagulation inside the passage. 1 Press the FUNCTION key in the local mode. 2 Select the [MAINTENANCE] by pressing the key. 3 Press the 4 Select the [STATION] by pressing the 5 Press the 6 Select the [MENT:DISWAY WASH] by pressing the or key. ENTER ENTER < L OC A L > or or key. MA I N T E N A NC E S T A T I ON key. 7 Press the 8 Remove the front cover.
Wash the ink discharge passage 9 Put washing liquid into the dropper, and drop on the caps to fill them. • Fill the washing liquid into the four caps. 10 Replace the front cover, and press the • Capping is performed. ENTER key. F i l l t he l i qu i d .
When the Machine Is Not Used for a Long Time (CUSTODY WASH) When the machine is not going to be used for a week or more, use the cleaning function for custody to clean the head nozzles and ink discharge passage. After this, keep the machine in custody. • Put on supplied goggles and gloves. Tools • UJ Cleaning swab (SPC-0386) • Gloves • Goggles • F-200 / LF-200 Washing Liquid (SPC-0568) 1 Press the FUNCTION key in the local mode.
When the Machine Is Not Used for a Long Time (CUSTODY WASH) 7 Put washing liquid into the dropper, and drop on the caps to fill them. • Fill the washing liquid into the four caps. 8 Replace the front cover, and press the 9 Set leaving time by pressing the press the ENTER key. key. • Capping is performed. • Usually set 10 min. (Set value: 1 to 99 min) • After the leaving time, cleaning is performed. 10 ENTER Press the END or key, and F i l l t he l i qu i d .
Washing the Head When you move the machine or you do not use the machine for a long time (for one month and more), wash the head and the ink discharge passage by the procedures below: • This machine is equipped with four heads. • To wash one head, four washing liquid cartridges (SPC-0516FS) are required at the minimum. Before performing the work, prepare new washing liquid cartridge. • When you wash all heads at the same time, prepare eight washing liquid cartridges with third part of them remains.
Washing the Head 7 Set the washing liquid cartridge to the ink station. • Set the washing liquid cartridge in the cartridge slot corresponding to the head to wash. The machine starts absorption of washing liquid. • When absorption of washing liquid has been completed, the right WA S H screen is displayed. R EMOV E 8 CARTR I DGE Remove the washing liquid cartridge. • Remove all set washing liquid cartridges. • When removing the washing liquid cartridge, the machine starts discharge of washing liquid.
Perform ink filling When head washing has been completed, “NOT FILLUP” is displayed on the screen and drawing cannot be performed as it is. Perform ink filling so that you may restart drawing after head washing. • Ink filling consumes much ink than that for the head cleaning ( check that ink remains enough in the cartridge. 1 Press the FUNCTION key in the local mode. 2 Select the [MAINTENANCE] by pressing the key, and press the ENTER key.
Setting nozzle face cleaning time When set times of drawing are completed, nozzle face of the head is cleaned automatically to remove ink droplets on the nozzle face. 1 Press the FUNCTION key in the local mode. 2 Select the [MAINTENANCE] by pressing the key, and press the ENTER key. 3 Select the [INT.WIPING] by pressing the key, and press the ENTER key. 4 Set the number of scanning times (OFF / 1 to 255) by pressing the or key, and press the ENTER key.
Maintenance for white ink White ink is easier precipitate than other inks. • This machine has the circulation function to prevent white ink precipitation. If you consume white ink of 2cc and more*1 every day, it is not necessary to perform white ink maintenance (white maintenance). • When you do not use this machine for a long time, white ink may settle down within the printer. If white ink settled down, it may cause nozzle clogging at drawing and you cannot draw normally.
Maintenance for white ink 6 Slowly shake the white ink cartridge more than twenty times right and left. • To prevent ink from leaking when you shake the cartridge, wear gloves and firmly cover the A part of the upper surface of the cartridge and the B part of the bottom surface of the cartridge with paper towels. Then, shake it more than twenty times right and left so that ink flows inside the cartridge. • If you shake it too strong, the pack inside may be damaged and it may cause ink leakage.
Cleaning of wiper The wiper sweeps ink stuck on the nozzle of the head. The wiper becomes tainted with ink or dusts during the operation of this machine. In order to keep the head in good condition, clean the wiper frequently. • When cleaning, be sure to put on the supplied goggles and gloves since you may get ink in your eyes. • Even if you cleaned the wiper, when Nozzle out or Ink dropping cannot be solved, try to replace the wiper.
Cleaning of wiper 6 Dip the washing liquid into the cleaning swab, and wipe dirt of the wiper nozzle. • Wipe the places shown in the right. • If the dirt of the wiper is heavy, replace the nozzle (SPA174). When fitting the nozzle, be careful not to put back to front. 7 Back Front After cleaning, replace the front cover, and press the key. ENTER S T A T I ON C OM P L E T E D : en t • Initializing starts. 8 Press the END key to finish.
Refilling antifreeze mixed water To cool the LED UV unit, put antifreeze mixed water into the cooling water tank in the cooling device. Cooling device Precautions for refilling • Water and antifreeze liquid compound ratio should be 2(water) to 1(Antifreeze liquid). • When only water is supplied to the cooling water tank without antifreeze liquid, it may damage the UV unit by freeze.
Refilling antifreeze mixed water Refilling antifreeze mixed water If water lack error is displayed, refill antifreeze mixed water. 1 Uncover the feed-water inlet and the air vent. feed-water inlet air vent cover 2 Remove all remaining water in the tank. 3 Mix antifreeze liquid with water. 4 Refill antifreeze liquid. 5 Cover the feed-water inlet and the air vent. (1) Remove all water in the tank with a provided syringe from the feed-water inlet.
4-36
CHAPTER 5 In Case of Trouble This chapter describes the actions to be taken when this machine develops any trouble or displays an error message. Before taking a phenomenon as a trouble ........................ 5-2 The machine cannot be energized ..............................................5-2 The machine cannot perform printing .........................................5-2 If image quality declines ..............................................................5-3 Resolving nozzle clogging ...............
Before taking a phenomenon as a trouble If something is wrong with the machine, the buzzer sounds and a corresponding error message is given on the LCD. Take an appropriate corrective measure in accordance with the message. The machine cannot be energized More often than not, this is due to improper connection of the power cable. Check that the power cable has been properly connected to the power outlet and the computer.
Before taking a phenomenon as a trouble If image quality declines Take measures as follows in accordance with the problem. If the problem does not improve, contact your local MIMAKI distributor or MIMAKI office to call for service. Development Corrective measure Lines/blur (1) Execute the head cleaning. ( P.2-12) (2) If slip of paper is attached in the head path, remove it. Large ink drop on media (1) Execute the head cleaning. ( P.2-12) (2) Remove the dust of the media.
Troubles for which error messages are given on the LCD If something is wrong with the machine, the buzzer sounds and a corresponding error message is given on the LCD. Take an appropriate corrective measure in accordance with the message. Warning Message Message < L OC A L > NO C A R T R I DGE < L OC A L > I N K N E A R E ND • Attach the ink cartridge(s) shown on the display. ( P.4-4) • Replace the ink cartridge shown on the display as soon as possible. ( P.
Troubles for which error messages are given on the LCD Message < L OC A L > C A P C L E A N I NG < L OC A L > C a s e We i g h t < L OC A L > I N K L V L L OW Solution • Execute the carriage out of the station maintenance, and clean the cap. • A case weight of 600 ml cartridge is not set. Set the case weight on “600 ml CARTRIDGE” of “MACHINE SET”. • Enter weight of the cartridge on “CART WEIGHT” of “SET UP”.
Error message When an error message is displayed, follow the table below and solve the problem. If the same error message is displayed again, contact a distributor in your district or our office. Message Solution E RROR 1 0 8 HD CONN E C T [ 1 2 3 4 5 6 7 8 ] • Turn the power of this machine off and turn it on after a while. • If the same error message appears again, contact a distributor in your district or our office to call for service.
Troubles for which error messages are given on the LCD Message E RROR 4 0 1 MO T OR X Solution • Turn the power of this machine off and turn it on after a while. • If the same error message appears again, contact a distributor in your district or our office to call for service.
Message E RROR 6 0 7 C A P C L E A N I NG E RROR 6 0 b W I P E R BO T T L E E RROR 6 0 c I NK T YPE E RROR 6 0 d R EMA I N I N K E RROR 6 0 e NO T COMP L E T E F U P E RROR 6 0 f Exp i r a t i on E RROR 6 1 0 NO T F I L L U P E RROR 6 1 1 C a s e We i g h t E RROR 6 1 2 I N K L V L L OW Solution • Execute the carriage out of the station maintenance, and clean the cap. • Execute the station maintenance and dispose of the ink in the wiper bottle. ( P.
Troubles for which error messages are given on the LCD Message E RROR 9 0 1 OP E R A T I ON Solution • Operate this machine correctly. E RROR 9 0 2 D A T A R EMA I N • Draw the all received data or clear the data. Then, change the settings. ( P.2-13 , P.3-9) E RROR 9 0 d NO H E A D S E L E C T • Head is not selected. Select a head to be cleaned or to be filled.
5-10
CHAPTER 6 Appendix Tables of specifications and functions of this unit are described. Specifications....................................................................... 6-2 Basic unit specifications ..............................................................6-2 Specifications for ink ...................................................................6-3 Function Flowchart..............................................................
Specifications Basic unit specifications Item Drawing head Method Specification Resolution Drawing mode x-dpi: 600 x-dpi: 900 x-dpi: 1200 x-dpi: 1800 Ink Ink supply Ink capacity Size Thickness Weight Maximum drawing area Absolute accuracy Distance accuracy Reproducibility Squareness Print gap adjustment Head anticollision device UV unit Waste ink tank Interface Media Command Stand-by In continuous operation In discontinuous operation Safety standards Ink safety Noise Power requirements Power consumpti
Specifications Specifications for ink As for the detail, ask the dealer or our branch. Item Feature Ink type Capacity of ink cartridge Shelf life During storage Storage temperature During shipping Parts No./ Specification Exclusive UV ink cartridge Black, magenta, cyan, yellow, right cyan, right magenta, primer, white, clear coat (Clear coat is LH-100 only.) 220 cc or 600 cc One year from the date of manufacture 15 °C to 35 °C (59 to 95 °F) 0 °C to 60 °C (32 to 140 °F) within 2 weeks permitted.
6-4
Function Flowchart When nozzle recovery is set, this is displayed. TEST key < L OCA L > T E S T DRAW ( SCAN D I R ) < EN T > T E S T DRAW NOZ Z L E RECOV ERY : ON ON, OFF T E S T DRAW ( F E ED D I R ) < EN T > * * T E S T DRAW * * CLEANING key < L OCA L > C L E AN I NG HE AD [ MCY K CLCLWW ] C L E AN I NG TYPE : n o r ma l ON/OFF select Head normal, soft, hard, Flushing*1 C L E AN I NG *- - - - - - - - - - - - - - - - - - *1 : UJF-3042HG: Supported from the firmware ver.3.
< L OCA L > F UNC T I ON WORK S E T < EN T > WORK S E T COMP L E T ED : en t F UNC T I ON SET J I G < EN T > SET J I G COMP L E T E : en t Only UJF-3042HG F UNC T I ON V ACUUM < EN T > V ACUUM V ACUUM : OF F ON, OFF F UNC T I ON HE AD HE I GH T < EN T > HE AD HE I GH T T A B L E S P ACER HE AD HE I GH T MED I A T H I CKNE S S < e n t > F UNC T I ON S E T OR I G I N < EN T > HE AD HE I GH T HE AD GA P HE AD HE I GH T T A B L E HE I GH T HE AD HE I GH T GA P CHE
Function Flowchart SET J I G J ig = NONE BBQ,Kebab,NONE HE AD HE I GH T T B L S P ACER : 1 0 0 mm 100,50,0 HE AD HE I GH T T H I CKNE S S : S : 100 1 . 0 mm Spacer=100：0.0 to 50.0 Spacer=50 ：50.0 to 100.0 Spacer=0 ：100.0 to 150.0 HE AD HE I GH T HE AD GA P : 1 . 5 mm 1.5 to 5.0 HE AD HE I GH T T B L HE I GH T S : 100 : 1 4 9 . 0 mm Spacer=100：100.0 to 150.0 Spacer=50 ：50.0 to 100.0 Spacer=0 ：0.0 to 50.
Followed Followed S E T UP I NK L A Y ERS S E T UP RE F RE SH S E T UP PR I OR I T Y S E T UP UV MODE S E T UP UV C u r i n g L e v e l < e n t > S E T UP UV A d d S c a n S E T UP WORK CHANGE S E T UP CAR T WE I GH T S E T UP F AN MODE S E T UP AU TO C L E AN I NG S E T UP PR I N T F L USH I NG < e n t > To be followed 6-8 S E T UP S E T UP RE S E T
Function Flowchart S E T UP I NK L A Y ERS :1 1 to 9 S E T UP RE F RE SH : L E V E L 1 0 to 3 S E T UP PR I OR I T Y : A L L HOS T ALL HOST, ALL PLOT, INDIVIDUAL S E T UP I NK L A Y ERS S E T UP PR I N T MODE : HOS T S E T UP F E ED COMP .
Followed F UNC T I ON MA I N T ENANCE To be followed 6-10 < EN T > MA I N T ENANCE S T A T I ON To be followed
Function Flowchart S T A T I ON MEN T : CARR I AGE OU T S T A T I ON P L E A S E WA I T S T A T I ON MEN T : W I P ER C L E AN I NG S T A T I ON COMP L E T ED : en t S T A T I ON MEN T : W I P ER BOT T L E S T A T I ON COMP L E T ED : en t S T A T I ON MEN T : WA S T E T ANK S T A T I ON COMP L E T ED : en t S T A T I ON MEN T : E XCH CAR T R I DGE S T A T I ON COMP L E T ED : en t S T A T I ON MEN T : CHECK F I L T ER S T A T I ON COMP L E T ED : en t S T A T I ON MEN T : NOZ Z L E WA SH
Followed Followed MA I N T ENANCE NOZ Z L E RECOV ERY < EN T > To be followed 6-12 To be followed
Function Flowchart Followed S T A T I ON MEN T : CUS TODY WA SH F i l l t he l i qu i d .
Followed To be followed 6-14 Followed MA I N T ENANCE I NK S E T MA I N T ENANCE I N T . W I P I NG MA I N T ENANCE F I L L UP I NK .
Function Flowchart I NK S E T [ LH - 1 0 0 ] S E L EC T : MCY K CLCLWW WA SH _ _ _ _ CLCLWW detect WA SH I NG REMOV E CAR T R I DGE P L E A S E WA I T Select the ink set.
Followed Followed MA I N T ENANCE UV L AMP To be followed 6-16 To be followed
Function Flowchart Followed F I L L UP I NK TYPE : f i r s t F I L L UP I NK [ L H - 1 0 0 ] S E L EC T : MCY K CLCLWW F I L L UP I NK HE AD [ MCY K CLCLWW ] Select the ink set.
Followed Followed MA I N T ENANCE HE AD WA SH MA I N T ENANCE WH I T E MA I N T A I N < e n t > To be followed 6-18 MA I N T ENANCE L I ST MA I N T ENANCE WI PE L EVE L MA I N T ENANCE D I S P L ACEMEN T MA I N T ENANCE I N FORMA T I ON
Function Flowchart MA I N T ENANCE HE AD [ MCY K CLCLWW ] WA SH REMOV E CAR T R I DGE WA SH S E T C L E AN TOO L detect WA SH I NG P L E A S E WA I T WA SH REMOV E CAR T R I DGE W I P ER C L E AN I NG COMP L E T ED detect detect WA SH I NG P L E A S E WA I T WA SH I NG P L E A S E WA I T WA SH REMOV E CAR T R I DGE WA SH S E T C L E AN TOO L WA SH I NG P L E A S E WA I T WA SH I NG P L E A S E WA I T T UB E C L E AN I NG COMP L E T ED : en t : en t WH I T E MA I N T A I N HE AD [ _ _ _ _
Followed F UNC T I ON MACH I NE S E T Followed < EN T > MACH I NE S E T S E T T I ME MACH I NE S E T MM / I NCH MACH I NE S E T 6 0 0 m l CAR T R I DGE < e n t > F UNC T I ON D I SP L AY < EN T > MACH I NE S E T K E Y BU Z Z ER MACH I NE S E T RAD I A TOR PUMP D I SP L AY En g l i s h Japanese , English 6-20
Function Flowchart S E T T I ME DA T E = 2 0 1 2 . 0 2 . 0 5 00 to 99 / 01 to 12 / 01 to 31 S E T T I ME T I ME = 10 : 20 : 00 00 to 23 / 00 to 59 MACH I NE S E T UP MM / I NCH : mm mm, inch MACH I NE S E T CAR T R I DGE : M MACH I NE S E T CA S E WE I GH T = 3 0 0 g M, C, Y, K, CL1, CL2, W1, W2 200 to 500 MACH I NE S E T K E Y BU Z Z ER : ON ON, OFF Displayed when the machine is UJF-3042HG.
6-22
D202466-14-07042014
© MIMAKI ENGINEERING CO., LTD.2014 IT UJF-3042HG: FW:4.0 UJF-6042: FW:1.
