Datasheet

ManualsBrandsMinco ManualsSensor Elements (Analogue)Resistance Thermometer -70 °C 400 °C Pt1000

Minco Bulletin TS-103 Order Desk: 763-571-3123 ¨ Fax: 763-571-0942 ¨ www.minco.com Page 11-1

Elements

Section 11: Ceramic Elements

•

Low cost thin-film elements

•

Wire wound elements

•

Accurate sensing from -200 to 850°C (-328 to 1582°F)

•

Wide choice of sizes and styles for application

versatility

•

Available from stock

550°C wire-wound elements..............11-2

400°C, 600°C thin-film elements ........11-2

850°C precision elements..................11-3

Installation ..........................................11-4

Extension leads..................................11-4

Custom elements...............................11-4

Summary of content (5 pages)

PAGE 1
Elements • Low cost thin-film elements • Wire wound elements • Accurate sensing from -200 to 850°C (-328 to 1582°F) • Wide choice of sizes and styles for application 550°C wire-wound elements ..............11-2 400°C, 600°C thin-film elements ........11-2 850°C precision elements ..................11-3 Installation ..........................................11-4 Extension leads..................................11-4 Custom elements ...............................
PAGE 2
Elements Wire-Wound and Thin-Film Elements Dimensions in inches (mm) R (0°C) Temperature range Leads Model -20 to 550°C (-4 to 1022°F) 0.006" (0.15 mm) ø Platinum S200PD 550°C wire-wound elements 0.040 ø (1.020) 0.45 (11.4) 0.75 (19) 0.058 ø (1.47) 0.40 (10.2) 0.75 (19) 0.077 ø (1.96) 0.30 (7.6) 0.75 (19) 0.100 ø (2.54) 0.40 (10.2) 0.75 (19) 0.135 ø (3.43) 0.40 (10.2) 0.077 ø (1.96) 0.135 ø (3.43) 0.010" (0.25 mm) ø Platinum alloy 100 W S201PD S202PD 0.014" (0.
PAGE 3
Elements 850°C Precision Elements Dimensions in inches (mm) 0.047 ø (1.2) 0.062 ø (1.6) 0.079 ø (2.0) 0.110 ø (2.8) 0.155 ø (3.9) 0.177 ø (4.5) 0.188 ø (4.8) Leads Response time in seconds Self-Heating Model Water, 1 m/s °C/mW Water, 0.4 m/s Air, 1.5 m/s 50% 90% 50% 90% 0.06 0.15 3.5 12.5 0.100 S270* 0.07 0.20 6.0 20.0 0.040 S271* 0.07 0.30 6.6 25.4 0.029 S272 0.08 0.35 7.0 25.0 0.020 S273 0.59 (15) 0.4 (10) 0.006" (0.15 mm) ø Platinum 0.98 (25) 0.
PAGE 4
Elements Installation and Accessories Ceramic elements can be assembled into probes or potted inside holes in heat sinks and platens. Ceramic cement is recommended for high temperature potting. Epoxy is recommended for intermediate temperatures. should connect extension leads as close as possible to the end of the element leads to maintain tolerance. Minco can supply elements with extension leadwires welded onto the sensor leads.
PAGE 5
Section 8 Stator Winding Detectors Section 4 Accessories Connection heads ...........................................................4-2 to 5-14 Spring-loaded holders.................................................................4-4 Fluid immersion fittings ...............................................................4-4 Thermowells ......................................................................4-6 to 4-8 Bayonet fittings ..........................................................................