Datasheet

ManualsBrandsMinco ManualsSensorsThermocouple Type K -200 °C 200 °C Polyamide

Minco Bulletin TS-103(A) Order Desk: 763-571-3123 ¨ Fax: 763-571-0942 ¨ www.minco.com Page 10-1

Thermal-Ribbons

Thermal-

Ribbons

Section 10: Thermal-Ribbons™

•

Thin, flexible RTDs and thermocouples

•

Fast response surface sensing in aerospace,

medical, and industrial devices

•

Rugged laminated construction

•

Kapton™, silicone rubber, Mylar™ insulation

•

All models available from stock

•

See page 9-6 for Thermal-Ribbons designed for pipe

mounting.

Miniature RTD Thermal-Ribbons .......10-2

Thin-film RTD Thermal-Ribbons.........10-2

Waterproof RTD Thermal-Ribbons ....10-2

Discoil™ Thermal-Ribbons.................10-3

Custom configurations.......................10-3

Strip sensing Thermal-Ribbons .........10-4

Thermistor Thermal-Ribbons .............10-5

Thermocouple Thermal-Ribbons.......10-5

Installation and accessories...............10-6

Summary of content (7 pages)

PAGE 1
Thermal-Ribbons • Thin, flexible RTDs and thermocouples • Fast response surface sensing in aerospace, medical, and industrial devices • Rugged laminated construction • Kapton™, silicone rubber, Mylar™ insulation • All models available from stock • See page 9-6 for Thermal-Ribbons designed for pipe mounting. Minco Bulletin TS-103(A) Miniature RTD Thermal-Ribbons .......10-2 Thin-film RTD Thermal-Ribbons.........10-2 Waterproof RTD Thermal-Ribbons ....10-2 Discoil™ Thermal-Ribbons.................
PAGE 2
Thermal-Ribbons Thermal-Ribbons and Thermal-Tabs Install these compact sensors anywhere for accurate point sensing and fast response. All Thermal-Ribbon models conform to EN60751 Class B tolerance when ordered with a PD platinum element. Thermal-Tab models use a thin-film RTD element. Element options Insulation Temp. range Leadwires 0.20 × 1.50 × 0.030" (5.1 × 38.1 × 0.8 mm) FA Kapton -200 to 200°C -328 to 392°F AWG 34, PTFE insulated 0.15 sec.
PAGE 3
Thermal-Ribbons Discoil™ Thermal-Ribbons Discoil RTD elements are wound in a single plane for faster time response. Dimensions W × L × T (max.) 0.79 × 1.87 × 0.055" (20 × 47.5 × 1.4 mm) solder pad version shown 1.00 × 1.25 × 0.090" (25.4 × 31.8 × 2.3 mm) Element options Insulation Temp.
PAGE 4
Thermal-Ribbons Strip Sensing Thermal-Ribbons These models average temperatures along their length to eliminate point measurement errors. Wrap them around cylinders or adhere them to flat surfaces. Dimensions W × L × T (max.) Element options 0.375 × 4.00 × 0.075" (9.5 × 101.6 × 1.9 mm) PB22 0.375 × 4.00 × 0.065" (9.5 × 101.6 × 1.7 mm) 0.50 × 1.25 × 0.050" (12.7 × 31.8 × 1.3 mm Insulation Temp. range Leadwires Time Features constant* Model -62 to 220°C -80 to 428°F 0.6 sec.
PAGE 5
Thermal-Ribbons Thermistor and Thermocouple Thermal-Ribbons Thermistor Thermal-Ribbon Dimensions W × L × T (max.) Element options 0.20 × 0.47 × 0.079" (5.0 × 12.0 × 2.0 mm) 0.20 × 0.60 × 0.118" (5.0 × 15.2× 3.0 mm) Insulation Temp. range Kapton with elastomer cover coat TF, TK Silicone rubber with elastomer cover and foil backing Leadwires AWG 26, PTFE insulated -50 to 125°C (-58 to 257°F) Time constant* Features Model 0.8 sec. Small, low-cost TS665 AWG 24, 1.3 sec.
PAGE 6
Thermal-Ribbons Installation and Accessories Thermal-Ribbons lend themselves to a variety of installation methods. You should avoid repeated bending during the installation process, and Thermal-Ribbons should not flex in use unless they are specifically designed to do so. Take care to secure leadwires so they do not pull against sensor bodies. Leadwires should be routed along the sensed surface a short distance so that they do not sink heat away from the sensing element.
PAGE 7
Section 4 Accessories Connection heads..............................................................4-2 to 4-3 Spring-loaded holders..................................................................4-4 Fluid immersion fittings .......................................................4-5, 4-10 Thermowells .......................................................................4-6 to 4-8 Bayonet fittings .............................................................................4-9 Extension fittings .........